Luxury Slate Shower Ruined by Limescale Restored in Surrey

In the south east of England, we suffer from hard water which as many of you have experienced can calcify on our showers leaving white limescale staining. Without fitting a water softener this limescale causes a problem around the home, particularly when the tiles are dark.

A good example of this problem was this large dark grey slate tiled shower at a house in Oxshott where the limescale had completely ruined the look of the black slate. The problem was most evident on the slate tiles on the floor but had also stained the slate split face slate tiles on the shower wall.

Slate Tiled Bathroom Before Renovation Oxshot

Oxshott is a village in Surrey between Leatherhead and Esher, a survey in 2010 by the Daily Telegraph asserted it was “the village with most footballers” in England and mentioned other celebrities who chose to live in the village probably because Chelsea Football Club have their main training ground in nearby Stoke D’Abernon; It is a beautiful area and is no surprise it is also known as ‘the most expensive village in England’.

The wet room was not that old, but due to the limescale staining was prematurely in need of attention. We often get calls from customers where they have use supermarket products to treat hard water stains, however these products are generally acidic, and this can make the problem worse. I would recommend you always read the back of the bottle before to check it is safe to use on natural stone before applying.

After inspecting the shower, I agreed with the client the best course of action, agreed a price and booked the job in for a later date.

Limescale Stained Slate Wet Room Cleaning

I returned on the agreed date and started work by first removing the existing sealer by applying Tile Doctor Remove and Go which is a multi-purpose stripper that’s formulated for use on natural stone. The product also draws out ingrained stains and removes heavy grease build-up. For best results spray the product onto the tile and then leave for it to soak in and get to work breaking down the coatings etc. After ten minutes the product is scrubbed into the stone which in this case meant by hand. The soiled solution can then be rinsed off the tiles with water. The grout was then cleaned by hand scrubbing in a strong dilution of Tile Doctor Pro-Clean followed by more rinsing.

The final part of preparation was to remove the limescale. This was done with a small handheld diamond block and a wire brush. The block is great for smoothing down all sorts of issues and being small it can get into tight areas. I then dried the whole room with an industrial blower. Slate cannot be sealed effectively when damp as it won’t cure properly. The blower is noisy but best in this situation and is very effective when a fast dry is needed.

Sealing a Slate Tiled Bathroom in Oxshott

After lunch I checked the area was nice and dry by testing the moisture content. I then sealed the whole area, wall and floor with Tile Doctor Colour Grow. Colour Grow, is a colour intensifying sealer that provides durable surface protection as well as allowing the surface to breath and enhance colour. For this project it darkened the tiles nicely and will provide protection from staining, making them much easier for the client to maintain moving forward.

The client was very happy with the lovely result. The bathroom looked clean and fresh again, now it is just a case of trying to keep on top of the limescale.

Slate Tiled Bathroom After Renovation Oxshot

 

Source: Slate Tile Cleaning and Renovation Service in West-Surrey

Renovating a Mouldy Marble Wet Room in Sheffield

The owner of this house in the village of Endcliffe Sheffield was unhappy about the state of their Marble wet room and called me in to do something about it. The main issue was that mould had built-up across the bathroom especially on the grout and silicone sealant, the Marble tiles were also looking dull and needed sprucing up.

Marble Bathroom Tiles Before Cleaning Endcliffe Sheffield

Dealing with Mould in a Wet Room

Mould thrives in moist warm conditions and without adequate ventilation it will start to take hold. Often in cases like this we advise clients to improve the power of their extractor fan or leave a window and a door open after a shower, in this case however the wet room had no windows. Another option you can try is to run the shower cold for a few minutes after you have used it, this decreases the temperature and removes moisture from the air. That tip is easily forgotten when your in a hurry so regular cleaning with Tile Doctor Duo-Clean which is a tile cleaner and mould remover should allow you to keep on top of the problem.

Marble Bathroom Tiles Before Cleaning Endcliffe Sheffield Marble Bathroom Tiles Before Cleaning Endcliffe Sheffield

In this case the Mould had really taken a hold and I knew form experience that scrubbing with a powerful cleaner like Duo Clean was unlikely to get the grout back to the pristine condition the customer wanted so I decided to strip out all the affected grout and silicone and replace with new. It took some time but I have a special electric grout removal tool that comes in handy for these situations and so it wasn’t long before I had removed the worse of it. This was followed by carefully removing the silicone sealant that ran between the shower tray and Marble wall tiles with a sharp knife.

Polishing Marble Wall and Floor Tiles

Next, I turned my attention to the Marble tiles which had lost their shine and become dull. Marble is hard stone and to get the best out of it we find its best to burnish them with a set of diamond encrusted burnishing pads that remove the dirt and slowly bring back the polished appearance. Normally when we talk about burnishing it’s in relation to stone floor tiles however these pads also come in small six-inch size as well which will fit a hand buffer or Angle Grinder.

Marble Bathroom Tiles During Cleaning Endcliffe Sheffield

Like floor burnishing the pads are applied in sequence starting with the coarse 400-grit pad and moving up through the 800, 1500 and finally the very fine 3,000-grit pad. The lower grit pads need to be lubricated with water and you rinse between each pad with water to remove the slurry that is generated.

Finishing the Marble Wet Room Renovation

With the Marble tiles now looking good it was time to protect them from future staining by sealing them with two coats of Tile Doctor Ultra-Seal which is a premium sealer that leaves a natural look that doesn’t darken the colour of the stone.

I left the re-grouting to last as its easier to remove grout from a sealed tile and then finished by putting back the silicone strip, both the grout and the silicone we chosen for their anti-mould formula and before leaving I gave some advice on how to keep on top of the mould problem going forward.

Marble Bathroom Tiles After Cleaning Endcliffe Sheffield

My client was delighted with the result and relieved that they would no longer feel embarrassed when visitors ask to use the bathroom.

Marble Bathroom Tiles After Cleaning Endcliffe Sheffield

 
 
Source: Marble Stone Cleaning and Polishing Service in Sheffield

Mould and Limescale stained Shower Cubicle renovated in Uxbridge

Ceramic and most Porcelain tiles are very easy to clean which makes them a good choice for shower cubicles, the one problem you will find though is that due to the cementitious nature of grout the top layer does attract dirt as can silicone. As a result, we recommend rinsing down showers with Tile Doctor Oxy-Pro on a regular basis or the problem will build. Mould can also be a problem especially if your bathroom is quite small or has inadequate ventilation to extract the hot steam in which mould thrives.

Ceramic Tiled Shower Cubicle Before Cleaning Uxbridge

This Ceramic tiled shower cubicle at a house in Uxbridge had all these problems and would need something much stronger to deal with the mould and remove the limescale which had also built up. Limescale from hard water is a problem that affects 60% of the UK with the South and East of England is particularly impacted due to the local chalk and limestone geology the water is filtered through. Buckinghamshire is known to have hard to very hard water and these tiny mineral deposits build up slowly on the surfaces of shower cubicles during use.

Deep Cleaning a Ceramic Tiled Shower Cubicle

To get the shower cubicle clean I began by spaying the tile and grout down with Tile Doctor Duo Clean which is a dual action product that is designed to clean grout and remove mould. You leave the product on the tiles for ten minutes and then scrub it in with a stiff brush, it’s hard work and you need to repeat in the stubborn areas, but it gets good results.

The tile and grout were then rinsed down with water and left to dry whilst I popped out for lunch. On my return I dried off any damp areas with a heat gun and took a step back to review the work I had done.

The results were good but unfortunately there were still a few dark stains in the grout which I was unlikely to be able to remove. When this happens, I find the best solution to achieve a consistent appearance is to apply a grout colourant to the grout. Tile Doctor grout colourants come in ten colours are relatively straight forward to apply, I always keep some of the popular colours in stock and on this occasion, I felt a White colourant would work best.

Normally the first stage would be to prepare the grout first with a pre-treater but given the grout had already been scrubbed hard I was able to move onto applying the colourant with a small brush. Grout Colourants not only recolour and rejuvenate the grout lines but also adds a barrier over the grout sealing it in and protecting it from further staining.

Whilst waiting for the colourant to dry I stripped out the mouldy sealant strip between the tile and shower tray and replaced with mould resistant silicone.

Ceramic Tiled Shower Cubicle Before Cleaning Uxbridge

The shower cubicle now looks much fresher and I’m sure will be a pleasure to take a shower in.
 
 
Source: Professional Renovation of a Ceramic Tiled Shower Cubicle in Buckinghamshire

Deep Cleaning Shower Tile Grout in Cumbria

We were asked to look at a renovating a bathroom shower at a house at the The Green, near Millom which was rather useful as it is a short distance from my own home. Millom is a small town in South West Cumbria that actually dates to 1251 when it was given a market charter by King Henry III.

Given the location it wasn’t long before I was able to pop round and review the shower installation. It was clear that the shower needed some Tile Doctor TLC, with mould being a major issue in the silicone seal and grout near the base of the shower.

Bathroom Shower Cubicle Before Renovation Millom

Mould thrives in warm damp environments such as shower cubicles and the problem can usually be traced to a lack of adequate ventilation. Improving the ventilation should resolve the problem permanently however if that’s not possible it can be controlled by regular use of products such as Tile Doctor Oxy-Pro shower cleaner or Tile Doctor Duo Clean which is a double action mould and grout cleaner. Other steps you can take include leaving the door open after a shower to improve cross ventilation and rinsing the shower down with cold water after a shower.

After reviewing the installation, we agreed on a price and I returned a few days later to carry out the work.

Cleaning Ceramic Bathroom Tile and Grout

On return the first thing we did was thoroughly clean the tile and grout using Tile Doctor Oxy-Gel, our high performance alkaline cleaner and de-greaser in gel form making light work of cleaning vertical tiled surfaces. The gel was scrubbed into all tile and grout surfaces and left to dwell for five minutes then thoroughly rinsed down with water. This process was repeated until we were happy with the result.

The next stage was to remove the mould riddled silicon and small areas of damaged grout at the base of the shower unit. This took some time to achieve as the silicon was in a very poor state. Once all traces of the silicone were removed we cleaned the area with more Oxy-Gel and carefully rinsed all the residues to stop us having any problems when re-applying new silicone.

Bathroom Shower Cubicle During Renovation Millom

The shower tray was cleaned of debris and a heat gun was used to completely dry all areas.

Replacing Shower Grout and Silicone Sealant

Finally, with the mould removed it was clear that a few areas of grout were crumbling and needed replacing. The old grout was raked out and a new batch of mould resistant grout was prepared and applied. Whilst that was drying I also replaced the silicone sealant between the shower tray and tile using a mould resistant silicone.

Bathroom Shower Cubicle After Renovation Millom

We asked the customer to not use the shower for at least 24 hours and as can be seen in the photographs the shower appearance was vastly improved. The customer is very pleased commenting that “it looks like new”.

Bathroom Shower Cubicle After Renovation Millom

 
 
Source: Tile and Grout Cleaning and Restoration Service in Cumbria

Renovating Three Shower Cubicles at Property in Sale, Cheshire

The photographs below are from one of three shower cubicles we were asked to clean and restore at a modernised Victorian property in SALE Cheshire. Ceramic tiles are glazed so very easy to keep clean, grout and silicone however are not and if you let mould build-up untreated it can very difficult to remove.

Mould likes a warm damp environment which can be reduced by improving the ventilation in the shower room, other steps you can take to reduce mould include always leaving the door open after a shower to improve cross ventilation and rinsing the shower down with cold water after a shower. Tile Doctor also have a product called Oxy-Pro that you can spray on your tiles after use.

Shower Cubicle Before Cleaning in Sale Shower Cubicle Before Cleaning in Sale

Sale is a town in Trafford, Greater Manchester but is historically part of Cheshire and dates to before the Middle Ages. A survey commissioned by the Royal Mail in 2017 highlighted Sale as the 4th most desirable town in England to live in and being so close to the city of Manchester makes it a popular choice for commuters.

Cleaning Ceramic Bathroom Tile and Grout

To get the grout clean Tile Doctor Pro-Clean was decanted into a spay bottle diluted with water and the solution was sprayed onto the grout lines. Pro-Clean in a strong and effective grout cleaner and after leaving it in place for about five minutes it was scrubbed in by hand using a stiff brush along the grout lines. I also gave the tile and cubicle glass a clean with Tile Doctor Oxy-Pro which comes in a ready to use spray bottle.

The next step was to carefully remove the old silicone sealant from around the edges of the shower cubicle using a sharp knife, so it could be replaced with new.

At this stage I took a step back to review the results of the cleaning, I wanted the best possible outcome for my customer and if more work was needed to get the shower looking it’s best now was the time. I concluded that the grout was much improved by unfortunately the mould staining was still visible in areas and that the best way to proceed would be to colour the grout.

Colouring Shower Tile Grout

Tile Doctor have a Grout Colourant product that’s available in ten different colours including White which I felt would be the best colour for the cubicle. Other colours include three shades of Grey, two shades of Brown and two shades of Beige as well as Black. The Grout Colourant is painted onto the grout lines using a small brush and I find a toothbrush works well for this purpose. Excess colourant needs to be removed from the tile before it sets, and I often find baby wipes work well for this purpose.

The grout colourant adds an epoxy barrier over the grout that is resistant to staining and much easier to clean than the grout itself. With this in place the grout will stay protected and the cubicle should keep its appearance for some time to come.

While the Grout Colourant was drying I replaced the silicone around the base of the shower cubicle using a premium mould resistant silicone that should be more resistant to staining.

Once the colourant and silicone had dried I gave the cubicle a final inspection and buffed up the ceramic tiles with a six-inch white pad fitted to a handheld buffer. As I mentioned before there were three shower cubicles to complete so as one was drying I was able to move onto another and as a result managed to complete all three in one day.

Shower Cubicle After Cleaning in Sale Shower Cubicle After Cleaning in Sale

 
 
Source: Shower Tile Cleaning and Renovation Service in Cheshire

Renovating Grubby Ceramic Tile and Grout in a Beckenham Bathroom

Recently I was asked to renovate the tile and grout of this windowless bathroom in a Beckenham flat which was not looking its best. The Ceramic tiles had become dull due to a build up of Limescale and the grout had become stained from shampoo dyes and mould.

Ceramic Bathroom Tiles Grout Before Cleaning Beckenham

Without strong ventilation and regular cleaning most bathrooms can end up with these problems however with the right products and techniques they can be renovated as you will see below.

Ceramic Bathroom Tiles Grout Before Cleaning Beckenham

Deep Cleaning Bathroom Tile and Grout

My first action was to apply a liberal amount of Tile Dr Oxy-Gel which is a strong alkaline tile and grout cleaning product that comes in a gel form. Being a gel it’s able to sticks to vertical surfaces for longer allowing it to break down the Limescale and soap residue that had taken up residence. Once it had been left to dwell for around thirty minutes, it was scrubbed off with water and a pan scrapper and then dried with a micro cloth. You can use this process with glazed ceramic tiles like these but for natural stone I would have used a different approach.

I then sprayed Tile Doctor Duo Clean, which is a grout cleaner and mould remover, onto the grout lines. I left the grout with the Duo Clean on it for about ten minutes before scrubbing and rinsing off with water.

The process was repeated where needed until I was happy that the tile and grout were as clean as possible however to really give the bathroom a fresh look I decided to completely renovate the grout with the application of a Grout Colourant.

Grout Colouring Bathroom Wall Tiles

There are ten colours to choose from in the Tile Doctor range of Grout Colourant’s and in this case I felt the best outcome would be to use a White colourant to match the tiles and restore the original look of the bathroom; the customer however wanted a grout colour that would provide a contrast against the white tiles, so in the end we opted for a light grey colour.

The colourant is easily applied directly to the grout and in this case I waited for the tiles to dry before applying two coats with the aid of a small brush making sure to remove any excess that comes into contact with the tile.

I finished the renovation by cutting out the original mastic sealant from around the bath and replacing with a new mould resistant silicone in white to match the bathtub.

Ceramic Bathroom Tiles Grout After Cleaning Beckenham

The bathroom now looks transformed and the epoxy grout colourant adds a layer of protection to the grout that will keep it looking good for some time to come.
 
 
Source: Bathroom Tile Cleaning and Restoration Service in Kent

Restoring Water Stained Porcelain Shower Tiles

Photographs below of a Porcelain tiled shower that had been installed at a house in Cheshunt the year before. The tiles were actually dark grey textured porcelain tile but hard water in the area had left very noticeable water stains and limescale deposits that were proving hard to remove with general cleaning.

Stained Black Porcelain Shower Tile Cheshunt Before Cleaning

Hardwater is basically water with a high mineral content which are historically recognised as being good for you, however it’s not so good for the bathroom where the minerals are left behind when the water evaporates.

On the initial visit to survey the tiles we ran a test clean on a small area to ensure we could return the tile back to its as new condition. All went well, and the customer booked us in to return later to complete the work.

Removing Limescale from Porcelain Shower Tiles

Work began by giving the shower tiles an initial clean with Tile Doctor Aqua-Pro which was worked into grout lines with detail brushes and a burnishing pad for the tile surface. This process removed all the Limescale and water marks.

A second clean was then carried out with Tile Doctor Duo-Clean which is a fast-effective double action cleaning solution that can remove mould and blackspots from grout and silicone. The solution was sprayed on the shower room floor and walls and left to soak in before being worked in with a stiff brush.

Stained Black Porcelain Shower Tile Cheshunt During Cleaning

The shower tiles were then rinsed with a steam cleaner to remove any trace of product and then buff the tiles with a hand-held white buffing pad to bring up their appearance.

To give it a neat waterproof finish we stripped out the old silicone sealant from around the base of the shower and replaced with new mould resistant silicone.

The shower took a whole day to complete but I think you will agree has been transformed by the process.

Stained Black Porcelain Shower Tile Cheshunt After Cleaning

Reducing the Impact of Hard Water

To minimise the impact of hard water some shower units will keep the shower running at a gradually decreasing temperature immediately after use. This has the effect of rinsing off the deposits before evaporation has chance to occur. Personally, we recommended you spray the shower tiles with Tile Doctor Aqua-Pro after use, this product is a bathroom tile cleaner that is ideal for the regular cleaning of all types of internal porcelain/ceramic bathroom/wet room tiles. Apply by lightly spraying a dilution of the cleaner and wipe over then water rinse and dry buff to finish.
 
 
Source: Porcelain Tile Cleaning and Renovation Service in Hertfordshire

Stained Shower Cubicle Renovation in Hove, East Sussex

Hove is a town in East Sussex which is confused with – and somewhat overshadowed by – its larger, more well-known neighbour, Brighton. In fact, the tendency for people to confuse Hove and Brighton is such that a running joke in the area amongst residents of Hove is to reply “Hove, actually” when they are asked if they live in Brighton.

But Hove is no small town – in fact, its home to more than 90,000 people. As the East Sussex Tile Doctor I am a frequent visitor to the Brighton and Hove area. Most recently, I was called to a property to address a Porcelain tiled shower cubicle which was really starting to annoy the owner.

She felt like she could never seem to keep it clean of grime and the dyes in soaps that invariably stain the grouting. As a result, the whole cubicle looked worse for wear – you can see this in the photo below.

Shower Room Tiles Before Grout Colouring in Hove Shower Room Tiles Before Grout Colouring in Hove

Not only did the customer want the tiles and grout cleaned up, but she had been impressed by some subway tiles she had seen where a darker grout had been used, she liked the effect it gave and wanted to see if it could be replicated. I suggested that we could clean up the tiles and recolour the grout using a Black Tile Doctor Grout Colourant. She accepted the quote for the work and I was able to get started soon after.

Cleaning Porcelain Shower Tiles and Grout

To begin the restoration, I gave the tile and grout a deep clean using Tile Doctor Pro-Clean, which is a highly effective alkaline-based cleaner for Tile, Stone and Grout.

This left the tiles looking fresher, but the grout lines – which were very badly stained – would as need to be recoloured for the best result. Before applying the Grout Colourant, the grout needed to be prepped in order to achieve a strong bond with the colourant. To do this I applied Tile Doctor Grout Clean-Up which is an acidic product normally used for removing grout smears but in this case, I used it to etch the surface of the grout. Once done I gave the grout a rinse with water to remove any trace of cleaning product.

Recolouring Shower Tile Grout

The final step in the restoration was to recolour the grout in black to achieve that subway effect the customer desired. There are actually ten different colours in the Tile Doctor Grout Colourant range, including Charcoal Grey, White, and Chocolate, as well as Black.
The colourant in basically painted onto the grout using an applicator brush, you then let it dry for a while and then wipe off any excess from the tile surface. It looks a little horrendous in the photographs above but wait until you see the final result.

Shower Room Tiles During Grout Colouring in Hove Shower Room Tiles During Grout Colouring in Hove

Once the grout colourant sets you find that not only does it effectively recolour and rejuvenate the grout, but it also makes a barrier over the grout effectively sealing it in and making it easier to clean in future.

The last step was to strip out the mould stained silicone sealant from around the base of the shower cubicle and replace with a quality mould resistant sealant. This final step really finished off the renovation and the photographs below show the outcome, which I think you will agree was quite a transformation. Thankfully, it was exactly what the customer was looking for!

Shower Room Tiles During Grout Colouring in Hove Shower Room Tiles After Grout Colouring in Hove

 
 
Source: Shower Tile and Grout Cleaning and Renovation Service in East Sussex

Renovating a Ceramic Tiled Shower Cubicle in Walshaw

The photograph below is of a Ceramic Tiled Shower Cubicle at a house in the lovely village of Walshaw which is part of the Metropolitan Borough of Bury, near Tottington and Bury. Most of the grout had darkened and some of the grout had cracked and had fallen out, the silicone seal at the bottom of the shower had gone mouldy in places and would also need replacing.

I find mould is a common problem in bathrooms and more prevalent in smaller bathrooms where the hot air and steam are unable to dissipate as easily creating the ideal environment for mould to grow. The solution is improved ventilation; alternatively you can keep on top of the situation by regular cleaning with Tile Doctor Duo Clean.

Ceramic Tiled Shower Grout Before Restoration Walshaw

Tile and Grout Cleaning

To tackle this installation I started by spraying the Tile and Grout down with Tile Doctor Duo-Clean, let it soak in for about ten minutes and then scrubbed it in by hand with a stiff brush followed by rinsing with water. This made a big improvement however there were still areas where the grout was still showing evidence of staining and would need a grout colourant applied to make it look like new again.

Next step however was to rake out the areas of grout that had crumbled and replace with new. Being a Tile Doctor this is something we are very familiar with and once the grout had dried I was able to move onto colouring.

Normally I would recommend using a Grout Colourant Pre-Treater before colouring however in this case I felt the scrub down I gave the grout with Duo-Clean would prepare the grout sufficiently and further preparation would not be necessary. The colourant is painted on using a small brush over the grout and any excess wiped off the ceramic tiles. The process makes a big difference to the look of a shower and the colourant provides a barrier over the grout making it easier to clean in future.

Last step was to strip out the silicone sealant between the shower wall and tray and replace with a new mould resistant sealant in white.

Ceramic Tiled Shower Grout After Restoration Walshaw

The shower cubicle was transformed and now looks as though it was recently installed.
 
 
Source: Shower Tile Cleaning and Sealing Service in Walshaw, Bury

Renovating an Old Ceramic Tiled Shower Cubicle in Berkshire

The photographs below are of a Ceramic Tiled Shower Cubicle installed in a retirement home in Maidenhead. The estimated installation for this bathroom is somewhere between twenty and thirty years and it was well overdue for an overhaul. First of all there was noticeable grout haze left on the tiles where it wasn’t polished off properly during installation and the second issue was the amount dirt and scum that had built up over the years. I suspect this was exacerbated by grout haze issue as it allowed the dirt to become trapped on the surface of the tile.

Retirement Home Shower Tile Grout Before Cleaning Maidenhead Retirement Home Shower Tile Grout Before Cleaning Maidenhead

Shower Tile and Grout Cleaning

A strong mix of Tile Doctor Pro-Clean was decanted into a spray bottle and applied to the tile and grout allowing it to dwell for a while before being scrubbed in with a stiff hand brush. This action worked to break down the years of dirt and grime that had built-up in the grout lines and on the surface of the ceramic tiles. The tiles were then rinsed down with water and repeated where required until I was satisfied.

The next step was to tackle the grout haze which refers to the smears of grout left on a tile by the tiller after installation; this should have been polished off as it can be difficult to remove once the grout has set. To remove I knew I would need to use an acid so a strong mix of Tile Doctor Grout Clean-up was applied using a sprayer bottle and then scrubbed off with an abrasive black pad. In some areas where the grout was proving extremely stubborn I found leaving Tile Doctor Acid Gel for a longer period of time before scrubbing in was more affective.

The shower tile and grout was then given another rinse with water and I could see that although the tiles were now clean and the grout was much improved the grout still looked stained in places so I decided the best course of action would be to apply a white grout colourant to restore a uniform appearance. Before applying that however I applied fresh grout to a few area where old had crumbled away.

Normally I would recommend using a Grout Colourant Pre-Treater before colouring however in this case I felt that the combination of products that had already been scrubbed into the grout would of more than prepared the surface to accept the colourant.

I left the shower to dry over lunch and then on my return used a heat gun to ensure the grout was bone dry before applying the grout colourant. The colourant is actually very easy to apply and is simply painted onto the grout using a small brush making sure to wipe off any excess from the ceramic tile as you go along. The process makes a big difference to the look of a shower and the colourant provides a barrier over the grout making it much easier to clean in future.

Last step was to strip out the old silicone sealant between the shower wall and tray and replace with a new mould resistant sealant in white and to give the tile a buff with a white pad fitted to a handheld buffer to remove any remaining residue.

Retirement Home Shower Tile Grout After Cleaning Maidenhead Retirement Home Shower Tile Grout After Cleaning Maidenhead

The shower cubicle was transformed and now looks as though it was recently installed. Certainly the customer was very pleased with the final result and left the following feedback.

“Dennis was the ultimate professional, prompt, polite and a pleasure to deal with, the transformation to the tiles in the shower is amazing, would have no hesitation in recommending him. A first class job”
 
 
Source: Shower Tile Cleaning and Renovation Service in Berkshire

Restoring the Shine on Marble Shower Tiles Ruined by Limescale Remover

We were recently received an enquiry from a customer in Ealing, East London who was concerned about their Marble Tiled Shower which had been damaged from the use of Viakal Limescale Remover. Unfortunately, this is a very common problem and we often receive calls from customers with similar issues. Limescale removal products such as Viakal and Cillit Bang are very effective but like any acidic product, they are very harmful to natural stone such as Limestone and Marble. With any cleaning product you should really read the label before use and in this case you will find they state the product should not be used on natural stone.

The Viakal had etched the surface of the Marble in several places where it had been applied and although the damage looked really bad I was happy to inform my customer there is a solution and that I could indeed restore the appearance of the stone.

Damaged Marble Shower Wall Before Restoration Ealing Damaged Marble Shower Wall Before Restoration Ealing

Polishing Damaged Marble Shower Tiles

My first task was to give the Marble tile and grout a good clean and remove any sealer and soap scum etc; to do this I used a strong dilution of Tile Doctor Pro-Clean scrubbed in with a small black scrubbing pad fitted to a hand-held machine. The Marble tiles were then rinsed with water to remove the soil generated by the cleaning process.

To fully restore the appearance of the Marble the next step required the application of coarse burnishing pads applied in sequence from very coarse to very fine using six-inch pads fitter to a handheld buffer. It’s a process that takes the polish off the stone and rebuilds it. A little water is needed to help lubricate with the coarser pads and the tiles are rinsed off between each one to remove any slurry generated during the process.

To achieve a very high shine the Marble tiles were then treated to an application of Tile Doctor Shine Powder which involves buffing crystallising polishing powder into the stone to build a deep durable finish

Sealing Marble Shower Tiles

The last step was to seal the Marble tile and grout to protect it going forward. Before sealing we needed to make sure that the tiles are dry and a damp meter is a very useful tool for this. A single coat of Tile Doctor Colour Grow was applied which is an impregnating sealer that occupies the pores in the stone whilst enhancing the natural colours in the Marble in the process.

Damaged Marble Shower Wall After Restoration Ealing Damaged Marble Shower Wall After Restoration Ealing

The work took three days in total but as you can see from the photographs on this page it was well worth the effort and the white streaky damage caused by the Viakal has now been removed and the stone has been transformed. My customer was very happy with the results and left the following feedback.

I had serious acid etchings from spraying Viakal on my marble shower box and basin. Didi and his partner did a good job of polishing out the majority of the acid etchings. It was a 3 day job for them, and over all I was happy with the result and service.
Edward T, London

 
 
Source: Marble Tile Cleaning and Renovation Service in Ealing, London

Shower Tiles Renovated following House Fire in Ayrshire

Below are a few photos of a smoke damaged shower cubicle where we were asked by an insurance company to restore the tiles following a house fire in the town of Ayr. Just south of Prestwick airport on the South West Coast of Scotland, Ayr is built along the river of the same name and dates all the way back to 1205.

You can see from the photograph below that the tiles how bad that smoke damage was. When we arrived work had already started to strip out the electric shower and screen removing a strip of tiles in the process. It was also clear that someone had also attempted to clean the ceramic tile and grout but had given up after realising how much work was needed.

Smoke Damanged Shower Tiles Before Restoration Ayr

Cleaning Smoke Damaged Tile and Grout

We had to give the tile and grout several deep cleans using a strong dilution of Tile Doctor Pro-Clean which was sprayed on, left to dwell for a while and then scrubbed in by hand. On reflection Oxy-Gel might have been a better product for the job as it has the same active ingredients but comes in a gel form which allows it to stick to vertical surfaces resulting in longer dwell times.

We managed to successfully remove all the smoke and soot from the surface of the tile and grout with this process. However although the grout was now clean I could see it was going to need more work if it was going to pass muster.

Smoke Damanged Shower Tiles During Restoration Ayr

Grout Colouring

To overcome the grout issue I decided to colour it with a White grout colourant; this was a perfect time to apply the colourant as the Pro-Clean had prepared the grout joints and would make a good bond with the colourant. I used three coats of white grout colourant in the end, each one applied by hand with a small brush. The colourant is basically painted on top of the existing grout and any excess wiped off the adjacent tile before it dries. It’s an epoxy based formula that becomes a long-lasting barrier protecting the grout and making it much easier to clean.

Following this I cleaned the tiles down again, this time with Neutral Tile Cleaner and then turned my attention to the stained silicone sealant around the base of the shower tray which was cut out and replaced with fresh new white silicone.

I gave the shower tray a clean as well and the final result was a very fresh looking shower cubicle which will soon back in action once the other trades finish their installations.

Smoke Damanged Shower Tiles After Restoration Ayr

 
 
Source: Bathroom Tile Cleaning and Renovation Service in Ayrshire

Mosaic Bathroom Tiles Deep Cleaned in Stockport

If you’re a landlord, it can be quite difficult to know what your tenants are getting up to and whether they are taking good care of your property. It’s usually only when major problems emerge that a landlord will get involved.

Such was the case with a recent customer of mine who owns a property in Stockport, a large town in Greater Manchester not too far south from the main city centre. The tenants of the property either neglected or didn’t know how to take care of the tiled shower walls in the bathroom. Over time, the condition of the tiles and grout had become so appalling that the landlord had to call Tile Doctor to see about restoring them.

Bath Shower Tile Before Refresh Stockport

Cleaning Dirty Shower Tiles

I began the restoration by cleaning the grout lines, which were truly filthy. This was done using a strong solution of Tile Doctor Pro Clean. Pro-Clean is an ideal product for cleaning up neglected tiles and grout, since it removes all manner of dirt, including the soap scum and grease which had built up on these shower walls over the course of several months.

The product was left to dwell for a couple of minutes before being scrubbed deep into the grout. The area was subsequently rinsed with fresh water to remove the soil. In some stubborn places, I didn’t achieve the desired result right away, so I repeated the cleaning process a couple of times.

When the grout and tiles were cleaned to the best of my abilities, I used my heat gun to dry the walls quickly. Next, I removed all the mouldy silicone around the shower, a process which proved quite tricky because the tiles were all quite small, and there was newer silicone on top of old, very mouldy silicone, so I had to dig in deep to get it all out.

After doing this, I had to clean and dry the gap between the tiles and the bath because the old mouldy silicone didn’t leave it in a pretty state.

Sealing Shower Tiles

After everything was cleaned and dried, I sealed the walls using Tile Doctor Wall Tile and Grout Sealer Aerosol Spray. What makes this such a brilliant product is how easy it is to use. It is a spray-on sealer that adds long lasting protection against water, dirt, grease, mould and limescale. This reduces the amount of maintenance required.

When I had finished sealing the tiles and grout, I applied new, high quality and mould resistant silicone. With that, the restoration was complete. The whole process took only a day’s work, but you must agree that a fantastic outcome was achieved. The landlord and tenants were very happy with it, remarking that if they didn’t know any better, they would’ve thought it was a brand-new installation.

Bath Shower Tile After Refresh Stockport

 
 
Source: Bathroom Tile Cleaning and Sealing Service in Stockport, Greater Manchester

Restoring Bathroom Wall Tile Grout in East Sussex

Anyone who wants to put their house up for sale should consider refurbishment projects that can help increase the value of the property and make it more appealing to potential buyers. This is especially the case in rooms with tiled floors or features, which many buyers find particularly attractive. If you’ve left your tiles – whether they’re in the bathroom, kitchen or elsewhere – in a bit of a state, chances are that it’ll put people off.

Recently, I was contacted by a customer who was in the process of refurbishing their house in Eastbourne prior to putting it up for sale. As part of the refurbishment, the customer wanted the Porcelain bathroom tiles to look ts absolute best for anyone viewing the property. While the bathroom room had been installed not too long ago, the grout was not looking very attractive.

Grout Before Changing Colour in Eastbourne Bathroom

This was due mainly to the fact that the grout was looking dark and stained. I was asked to give the tiles and grout a thorough clean before recolouring the grout to make it lighter and more appealing.

Cleaning and Re-Colouring Porcelain Shower Tiles and Grout

To achieve the best results, the grouting in shower cubicles needs to be cleaned before it can be recoloured. To do this, I used Tile Doctor Duo Clean, a product which acts fast to removes any mould and black spots from the grout. If necessary, it can also be used to clean plastic or enamel baths and showers.

The product was applied and then scrubbed into the grout carefully using a specialised grout brush, and the area was left to dry. Once the cubicle was dry, I applied the Tile Doctor Grout Colourant in small sections, so that I could wipe off any excess from the tile surface before it dried.

Grout During Changing Colour in Eastbourne Bathroom

Tile Doctor Grout Colourants are available in 10 different colours, but in this case the customer opted for a normal white as it contrasts nicely with the grey tiles. The Colourant not only recolours the grout lines; it also seals and rejuvenates them.

Grout After Changing Colour in Eastbourne Bathroom

The shower room was quite large, so the job took most of the day to complete. But it was certainly worth it. The customer was very pleased with the results, and we wish them the best of luck with selling the property.

Grout After Changing Colour in Eastbourne Bathroom

 
 
Source: Bathroom Tile and Grout Cleaning in East Sussex

Bathroom Tile Grout Makeover in Greenock

This bathtub with shower over was at a house in the old shipbuilding port of Greenock within the historic county of Renfrewshire. I’m not sure you can appreciate it from the before photograph below, but the grout was white and was starting to discolour. The owner of the house didn’t want it to get any worse and asked us for help.

Changing Grout Colour in Greenock Bathroom Before

Preparing the Grout

We discussed the options and the benefits of applying a grout colour which would not only change the colour but also add a layer of protection over the grout which would be much easier to keep clean going forward.

With the decision made we set about cleaning the grout first with a Grout Colourant Pre-Treater that cleans and etches the grout resulting in a better bond with the grout colourant. This was followed by rinsing the grout with water to remove any dirt and remove the traces of pre-treater before drying it off with a heat gun ready for the next step.

Grout Colouring

The customer had decided on a Chocolate grout colour, so it would blend in with the brown tiles more effectively. So, once the grout has dried two coats of Tile Doctor Grout Colourant were applied over the grout with a small brush. This product is basically painted on top of the existing grout any any excess wiped off the adjacent tile before it dries. It’s an epoxy based formula that becomes a long-lasting barrier protecting the grout and as I mention before making it much easier to clean.

Last step before leaving was to strip out the stained silicone sealant between the top of the bath and tile and replaced with fresh new white silicone to match with the white bathroom suite.

Changing Grout Colour in Greenock Bathroom After

The job only took a day to complete and the owner was very pleased with the way the tiles now looked.
 
 
Source: Ceramic Tile Cleaning and Restoration Service in Greenock

Dealing with Stained Tile and Grout in an Edinburgh Shower Cubicle

Porcelain is a popular choice for tiles in modern homes due to its superior durability. It also makes a particularly suitable material for shower tiles because of its natural water resistance. Nonetheless, Porcelain tiles – just like any other type of tile – still require routine cleaning and maintenance to stay looking fresh and attractive.

This is especially the case for shower tiles, as they are subject to mould and scum caused by exposure to the dyes in shampoos and soaps etc which as well as staining the tiles can have a dramatic effect on the grout. Below is a photo of a Porcelain shower cubicle I was asked to restore in Edinburgh. The process for restoring these types of tiles is relatively quick and easy, providing you use the right products and methods. Here’s how I did it.

Shower Grout Before Restoration in Edinburgh

Cleaning and Sealing Porcelain Shower Cubicle Tiles

To begin refreshing this cubicle, I gave the whole area – paying particular attention to the grout lines – a scrub down using Tile Doctor Duo Clean. Duo Clean is our product of choice for the removal of the common mould and soap scum that builds up on cubicles like this one.

Next, I rinsed down the area with fresh water to remove any trace of cleaning product and then left it to dry for a short period of time. It’s difficult to get the grout lines perfectly clean, especially after years of neglect, but we can resolve the situation by simply recolouring the grout.

Shower Grout During Restoration in Edinburgh

I this case I felt the grout although cleaner from when I started did need more work so I decided to go ahead and apply a Grout Colourant. Tile Doctor has a range of Grout Colourants available in ten colours so I painted on three coats of the white colourant which really improved the look of the grout leaving it clean and fresh. Another advantage is the colourant acts as a barrier on top of the grout sealing the grout joint and protecting them from further staining. Other popular colours available in the range include Black, Cappuccino, and three shades of Grey.

Finally, I ripped and out and replaced the mouldy silicone around the base of the shower cubicle and replaced it with fresh.

Shower Grout After Restoration in Edinburgh

The client was very impressed with the speedy restoration. Before leaving the property, I explained that rinsing down the shower cubicle with fresh water after every use can help to reduce the effect of staining and leaving the door and window open after a shower improved ventilation and inhibit the growth of mould. Naturally you can always give me call if the situation gets out of hand.
 
 
Source: Shower Tile Cleaning and Renovation Service in Edinburgh

45 Shower Cubicles Deep Cleaned at Student Accommodation

Earlier in the year we were contacted by the facilities manager of one of the student apartment blocks in Oldham which provides accommodation for the students of Oldham University. They were looking for a firm to revamp the student en-suite bathrooms during the summer recess. The building has 270 apartments and we had been asked to quote for the renewal of the ceramic tile and grout of around 45 shower cubicles (possibly more) which were judged to be in a bad state and beyond the ability of their in-house cleaning team.

The University runs degree courses from Accounting to Sports Coaching and as you can image Students are not known for their cleanliness so we knew we would have our work cut out completing the assignment on time.

Several companies competing for the work however after successfully demonstrating what we can do with a patch test in one of the bathrooms and comparing of quotes I’m pleased to say the facilities company awarded us the contract!

Student Shower Cubicle Before Cleaning in Oldham

Tile and Grout Cleaning

We returned in the summer and facing a time limit to complete the work we worked out a system whereby we would spray the Tile and Grout down with Tile Doctor Duo-Clean, let it soak in for about ten minutes and then scrubbed it in by hand with a stiff brush. Duo Clean is an effective double action grout cleaner and mould remover that can remove mould and blackspot from grout and silicone. It’s really useful for cleaning shower tiles as the spay attachment mixes the product with air as its spayed onto the surface allowing it to stick to vertical surfaces more easily. Once the tile and grout was clean it was rinsed off with water and stubborn areas re-treated until clean.

Duo Clean is effective at dealing with Mould on Silicone in most situations however some of the silicon sealant was beyond cleaning so in these cases the old Silicone was stripped out and replaced with new.

We were able to clean all the shower tile and grout using this process however I had brought a long a few Grout Colouring kits as a back-up solution just in case. Once the grout is clean the colourant is painted on using a small brush and makes a huge difference to the look of a shower. There also inexpensive and provide a barrier over the grout so it keeps its appearance for longer.

There were a lot of bathrooms to cover so once the cubicle was spotless we immediately moved onto the next one completing the whole project three days ahead of the due date.

Student Shower Cubicle After Cleaning in Oldham

The facilities manager was delighted with results and timing of our work and it just goes to show that using the right cleaning products can save you time and money compared to the alternative of re-grouting.
 
 
Source: Shower Tile and Grout Cleaning Service in Oldham

Restoring Damaged Marble Shower Tiles in Surrey

Marble tiles are a fantastic choice of stone for a shower cubicle because of its distinctive characteristics and quality. It can really add a luxurious feel and when used in a bathroom take it to the next level.

However, it’s extremely important to note that Marble like all natural stone is a porous and acid-sensitive material. It must therefore be cleaned with care using suitable products. This particular Marble tiled shower cubicle at a property in Leatherhead is a good example of this done wrong. The owner had used an acid-based cleaning product to clean the stone, resulting in damage to the sealer and causing unappealing streaks to form.

Marble Shower Wall Leatherhead Before Cleaning

This type of damage can appear irreparable but, with the right combination of cleaning methods and products, it can be fixed. Once the old sealer has been removed, and the tiles have been cleaned, polished and re-sealed, they can look as a good as new. Here’s how I helped this customer restore the Marble shower cubicle.

Cleaning and Polishing a Marble Shower Cubicle

To begin the restoration, I scrubbed the dirty grout lines using Tile Doctor Pro-Clean, which is a highly reliable and multi-purpose alkaline-based product. I then rinsed the tiles with water to remove the traces of cleaning product.

Next, I moved on to the polishing stage of the restoration – what we often refer to as burnishing. This involved the use of small six-inch diamond-encrusted burnishing pads applied with a hand buffer and with different levels of grit – ranging from Coarse to Very Fine. I started with the Coarse grit pad and worked my way sequentially through our four-pad system, polishing the stone with Medium, Fine and eventually the Very Fine pad to really bring up the polish.

Sealing a Marble Shower Cubicle

Once the shine had returned to the Marble and the damage had been removed, I re-sealed the tiles using two coats of Tile Doctor Colour Grow, a penetrating sealer designed to enhance the natural colours and patina of the stone. Once dry, I gave the tiles a final polish with a white buffing pad to put the finishing touches on the restoration.

Marble Shower Wall Leatherhead After Cleaning

The customer was thrilled with the results, saying:
“I’m really happy with the result and we will make sure we don’t use supermarket cleaners again on natural stone. Rupert was a very personable tradesman who took pride in what he was doing. He has identified Tile Doctor Neutral Tile Cleaner as being the product we should have used in the first place and has sent me the website details.”
Another satisfied customer!
 
 
Source: Marble Tile Cleaning and Restoration Service in Surrey

Fixing a Leaking Luxury Wet Room in Yorkshire

Travertine is a distinct and highly aesthetic material which offers unique characteristics and colouring that not many other types of stone can offer. It looks great when used on tiled floors and in this case shower cubicles however like any natural stone it does need maintenance.

Travertine WetRoom Harrogate Before Cleaning

A good example of this point was this Travertine wet room in Harrogate, which comprised of large format Travertine tiles on the floor and Travertine mosaic tiles on the walls. It was in poor condition and to make things worse had been leaking for years. A local plumber had tried to resolve the leak, but to no avail. At this point, the property owner was desperately searching for a solution, and decided to contact me to see what could be done both to restore the appearance of the wet room and fix the leakage.

Travertine WetRoom Harrogate Before Cleaning

Cleaning a Travertine Tiled Wet Room

On first inspection of the wet room, l couldn’t see any obvious problems that might be causing the leak, however the white silicon did look a bit questionable and had already decided that would need replacing. To start I turned my attention to cleaning the whole shower cubicle, including the tile and grout.

I did this by applying Tile Doctor Pro-Clean, which is a high alkaline cleaner, to remove the mould, soap scum and dyes caused by daily exposure to acidic soap and shampoos. These issues can build up exceptionally quickly if care is not taken to regularly rinse down the shower after each use.

During this process, I noticed grout haze had been left on the surface of the tiles following installation and so treated the problem with Tile Doctor Acid Gel, which is a blend of hydrochloric and phosphoric acid in gel form. Being a gel, this product works particularly well on vertical surfaces because it is easier to control.

The next step was to resolve the leakage problem, starting by removing all the old and unattractive white silicon. When l removed the silicon, I could see that it was black with mould at the back. It was clear to me then that water was getting behind it and this was the cause of the leak. Also, this revealed a 2-3mm gap between the wall and the base of the shower. The gap was damp and mould had collected there, so this needed to be scraped out manually and the gap dried with a heat gun. Finally, l filled the gap with grout to seal it and left the wet room to dry overnight.

Travertine WetRoom Harrogate Before Cleaning

Sealing a Travertine Tiled Wet Room

The next day, I returned to the property and sealed the grout with Tile Doctor Ultra-Seal. This is a premium, natural-look, penetrating sealer formulated to provide maximum stain protection and allow moisture vapour transmission. To finish the restoration, I applied fresh, clear silicon around the base.

Travertine WetRoom Harrogate After Cleaning

In my opinion, white silicon should never have been used with stone, as clear silicon is far more suitable and more pleasing to the eye. Certainly, my customer agreed – and she was very pleased with the result and no more leak.

Travertine WetRoom Harrogate After Cleaning

 
 
Source: Travertine Cleaning and Sealing Service in North Yorkshire

Renovating Porcelain Hallway Floor Tiles in Didcot

Available in a variety of styles and designs Porcelain tiles are harder than normal Ceramic tiles and are known for their durability and water resistance, making them ideal for use in shower cubicles and bathrooms.

However, as I’m sure most people already know, shower tiles are not the easiest to keep clean and fresh. These tiles are exposed daily to a multitude of acidic soaps and shampoo dyes, and if proper precaution is not taken to rinse away the excess after using the shower, mould will grow very quickly on the grout.

This shower cubicle, constructed from Porcelain tiles, is a typical example of this. As you can see from the photo below, the mould problem was very apparent. I was asked by the property owner, who lives in Didcot, a railway town in South Oxfordshire, to refresh it after what must have been years of neglect. Here’s how I did it.

Porcelain Shower Before Renovation in Didcot

Cleaning a Porcelain Tiled Shower Cubicle

The first process in restoring this shower cubicle was to spray the walls with Tile Doctor Duo Clean, which is both a grout cleaner and a mould remover. I left it to dwell for 45 minutes, before proceeding to scrubbing into the grout with a stiff brush. I worked in sections, spraying more Duo Clean onto the tiles as I moved along the length of the walls.

Following this, I rinsed the entire cubicle with fresh water to remove any traces of chemicals and used my wet-vac machine to dry it quickly. The next process was to remove the old, mouldy silicone and replace it with fresh silicone.

Sealing a Porcelain Tiled Shower Cubicle

With the shower cubicle now fresh and clean, it was now time for me to seal the grout and tiles.

I did this using Tile Doctor Wall Grout Sealer Spray, which is a water-based grout sealer that prevents oil, water and acid-based contaminants – including soaps and shampoos – from spoiling the appearance and colour of grout. It does this while allowing for moisture vapour transmission.

Check out the photo below – you can see that after a short day’s work, the appearance of the cubicle has been completely transformed. The customer was very pleased with the result and the addition of the sealer will ensure it stays this way for some time to come.

Porcelain Shower After Renovation in Didcot

 
 
Source: Shower Tile Cleaning and Renovation Service in Oxfordshire