Renovating a Ceramic Tiled Shower Cubicle in Walshaw

The photograph below is of a Ceramic Tiled Shower Cubicle at a house in the lovely village of Walshaw which is part of the Metropolitan Borough of Bury, near Tottington and Bury. Most of the grout had darkened and some of the grout had cracked and had fallen out, the silicone seal at the bottom of the shower had gone mouldy in places and would also need replacing.

I find mould is a common problem in bathrooms and more prevalent in smaller bathrooms where the hot air and steam are unable to dissipate as easily creating the ideal environment for mould to grow. The solution is improved ventilation; alternatively you can keep on top of the situation by regular cleaning with Tile Doctor Duo Clean.

Ceramic Tiled Shower Grout Before Restoration Walshaw

Tile and Grout Cleaning

To tackle this installation I started by spraying the Tile and Grout down with Tile Doctor Duo-Clean, let it soak in for about ten minutes and then scrubbed it in by hand with a stiff brush followed by rinsing with water. This made a big improvement however there were still areas where the grout was still showing evidence of staining and would need a grout colourant applied to make it look like new again.

Next step however was to rake out the areas of grout that had crumbled and replace with new. Being a Tile Doctor this is something we are very familiar with and once the grout had dried I was able to move onto colouring.

Normally I would recommend using a Grout Colourant Pre-Treater before colouring however in this case I felt the scrub down I gave the grout with Duo-Clean would prepare the grout sufficiently and further preparation would not be necessary. The colourant is painted on using a small brush over the grout and any excess wiped off the ceramic tiles. The process makes a big difference to the look of a shower and the colourant provides a barrier over the grout making it easier to clean in future.

Last step was to strip out the silicone sealant between the shower wall and tray and replace with a new mould resistant sealant in white.

Ceramic Tiled Shower Grout After Restoration Walshaw

The shower cubicle was transformed and now looks as though it was recently installed.
 
 
Source: Shower Tile Cleaning and Sealing Service in Walshaw, Bury

Renovating an Old Ceramic Tiled Shower Cubicle in Berkshire

The photographs below are of a Ceramic Tiled Shower Cubicle installed in a retirement home in Maidenhead. The estimated installation for this bathroom is somewhere between twenty and thirty years and it was well overdue for an overhaul. First of all there was noticeable grout haze left on the tiles where it wasn’t polished off properly during installation and the second issue was the amount dirt and scum that had built up over the years. I suspect this was exacerbated by grout haze issue as it allowed the dirt to become trapped on the surface of the tile.

Retirement Home Shower Tile Grout Before Cleaning Maidenhead Retirement Home Shower Tile Grout Before Cleaning Maidenhead

Shower Tile and Grout Cleaning

A strong mix of Tile Doctor Pro-Clean was decanted into a spray bottle and applied to the tile and grout allowing it to dwell for a while before being scrubbed in with a stiff hand brush. This action worked to break down the years of dirt and grime that had built-up in the grout lines and on the surface of the ceramic tiles. The tiles were then rinsed down with water and repeated where required until I was satisfied.

The next step was to tackle the grout haze which refers to the smears of grout left on a tile by the tiller after installation; this should have been polished off as it can be difficult to remove once the grout has set. To remove I knew I would need to use an acid so a strong mix of Tile Doctor Grout Clean-up was applied using a sprayer bottle and then scrubbed off with an abrasive black pad. In some areas where the grout was proving extremely stubborn I found leaving Tile Doctor Acid Gel for a longer period of time before scrubbing in was more affective.

The shower tile and grout was then given another rinse with water and I could see that although the tiles were now clean and the grout was much improved the grout still looked stained in places so I decided the best course of action would be to apply a white grout colourant to restore a uniform appearance. Before applying that however I applied fresh grout to a few area where old had crumbled away.

Normally I would recommend using a Grout Colourant Pre-Treater before colouring however in this case I felt that the combination of products that had already been scrubbed into the grout would of more than prepared the surface to accept the colourant.

I left the shower to dry over lunch and then on my return used a heat gun to ensure the grout was bone dry before applying the grout colourant. The colourant is actually very easy to apply and is simply painted onto the grout using a small brush making sure to wipe off any excess from the ceramic tile as you go along. The process makes a big difference to the look of a shower and the colourant provides a barrier over the grout making it much easier to clean in future.

Last step was to strip out the old silicone sealant between the shower wall and tray and replace with a new mould resistant sealant in white and to give the tile a buff with a white pad fitted to a handheld buffer to remove any remaining residue.

Retirement Home Shower Tile Grout After Cleaning Maidenhead Retirement Home Shower Tile Grout After Cleaning Maidenhead

The shower cubicle was transformed and now looks as though it was recently installed. Certainly the customer was very pleased with the final result and left the following feedback.

“Dennis was the ultimate professional, prompt, polite and a pleasure to deal with, the transformation to the tiles in the shower is amazing, would have no hesitation in recommending him. A first class job”
 
 
Source: Shower Tile Cleaning and Renovation Service in Berkshire

Shower Tiles Renovated following House Fire in Ayrshire

Below are a few photos of a smoke damaged shower cubicle where we were asked by an insurance company to restore the tiles following a house fire in the town of Ayr. Just south of Prestwick airport on the South West Coast of Scotland, Ayr is built along the river of the same name and dates all the way back to 1205.

You can see from the photograph below that the tiles how bad that smoke damage was. When we arrived work had already started to strip out the electric shower and screen removing a strip of tiles in the process. It was also clear that someone had also attempted to clean the ceramic tile and grout but had given up after realising how much work was needed.

Smoke Damanged Shower Tiles Before Restoration Ayr

Cleaning Smoke Damaged Tile and Grout

We had to give the tile and grout several deep cleans using a strong dilution of Tile Doctor Pro-Clean which was sprayed on, left to dwell for a while and then scrubbed in by hand. On reflection Oxy-Gel might have been a better product for the job as it has the same active ingredients but comes in a gel form which allows it to stick to vertical surfaces resulting in longer dwell times.

We managed to successfully remove all the smoke and soot from the surface of the tile and grout with this process. However although the grout was now clean I could see it was going to need more work if it was going to pass muster.

Smoke Damanged Shower Tiles During Restoration Ayr

Grout Colouring

To overcome the grout issue I decided to colour it with a White grout colourant; this was a perfect time to apply the colourant as the Pro-Clean had prepared the grout joints and would make a good bond with the colourant. I used three coats of white grout colourant in the end, each one applied by hand with a small brush. The colourant is basically painted on top of the existing grout and any excess wiped off the adjacent tile before it dries. It’s an epoxy based formula that becomes a long-lasting barrier protecting the grout and making it much easier to clean.

Following this I cleaned the tiles down again, this time with Neutral Tile Cleaner and then turned my attention to the stained silicone sealant around the base of the shower tray which was cut out and replaced with fresh new white silicone.

I gave the shower tray a clean as well and the final result was a very fresh looking shower cubicle which will soon back in action once the other trades finish their installations.

Smoke Damanged Shower Tiles After Restoration Ayr

 
 
Source: Bathroom Tile Cleaning and Renovation Service in Ayrshire

45 Shower Cubicles Deep Cleaned at Student Accommodation

Earlier in the year we were contacted by the facilities manager of one of the student apartment blocks in Oldham which provides accommodation for the students of Oldham University. They were looking for a firm to revamp the student en-suite bathrooms during the summer recess. The building has 270 apartments and we had been asked to quote for the renewal of the ceramic tile and grout of around 45 shower cubicles (possibly more) which were judged to be in a bad state and beyond the ability of their in-house cleaning team.

The University runs degree courses from Accounting to Sports Coaching and as you can image Students are not known for their cleanliness so we knew we would have our work cut out completing the assignment on time.

Several companies competing for the work however after successfully demonstrating what we can do with a patch test in one of the bathrooms and comparing of quotes I’m pleased to say the facilities company awarded us the contract!

Student Shower Cubicle Before Cleaning in Oldham

Tile and Grout Cleaning

We returned in the summer and facing a time limit to complete the work we worked out a system whereby we would spray the Tile and Grout down with Tile Doctor Duo-Clean, let it soak in for about ten minutes and then scrubbed it in by hand with a stiff brush. Duo Clean is an effective double action grout cleaner and mould remover that can remove mould and blackspot from grout and silicone. It’s really useful for cleaning shower tiles as the spay attachment mixes the product with air as its spayed onto the surface allowing it to stick to vertical surfaces more easily. Once the tile and grout was clean it was rinsed off with water and stubborn areas re-treated until clean.

Duo Clean is effective at dealing with Mould on Silicone in most situations however some of the silicon sealant was beyond cleaning so in these cases the old Silicone was stripped out and replaced with new.

We were able to clean all the shower tile and grout using this process however I had brought a long a few Grout Colouring kits as a back-up solution just in case. Once the grout is clean the colourant is painted on using a small brush and makes a huge difference to the look of a shower. There also inexpensive and provide a barrier over the grout so it keeps its appearance for longer.

There were a lot of bathrooms to cover so once the cubicle was spotless we immediately moved onto the next one completing the whole project three days ahead of the due date.

Student Shower Cubicle After Cleaning in Oldham

The facilities manager was delighted with results and timing of our work and it just goes to show that using the right cleaning products can save you time and money compared to the alternative of re-grouting.
 
 
Source: Shower Tile and Grout Cleaning Service in Oldham

Cleaning a Ceramic Tiled Shower Cubicle in Herstmonceux

We often get asked to do bathroom refresh and end of tenancy tile cleans however it’s a good job I’m not squeamish as this ceramic tiled shower cubicle was in a bad way.

Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux

The property was in the historic village of Herstmonceux in the Wealden District of East Sussex and apparently it had been leased to students who it seems were averse to cleaning, no surprise there.

Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux

Cleaning Ceramic Tiled Shower Cubicle

The first step was to remove the plastic product holder to expose the tile and grout, which revealed more staining and black mould.

Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux Ceramic Tiled Shower Cubicle Before Cleaning Herstmonceux

With that removed I sprayed the Tile and Grout with Tile Doctor Oxy-Gel which works better than liquid products as being gel based it sticks to the wall tile and grout and really gets to work breaking down the dirt. I left this for a few minutes before scrubbing it and then rinsing it off with water. I had a problem with a patch of grout which was beyond cleaning and concerned it was going to upset the whole job I raked out it and applied new grout.

Grout Colouring Shower Wall Tiles

With the tiles now clean and fresh grout dried the next step was to apply a White Grout Colourant to ensure all the grout had a consistent appearance. Although time consuming the grout colourant is easily applied with a small brush and then you wipe off any excess that gets onto the tile.

The next step was to strip out the mastic silicone sealant strip from around the base of the shower cubicle and replace with new. I used high quality silicone sealant that left nice lines and fresh look, don’t use cheap sealant as it will soon discolour and some have been known to shrink.

Last step was to replace the plastic product holder which had been cleaned.

Ceramic Tiled Shower Cubicle After Cleaning Herstmonceux

Quite a difference I think you’ll agree. Future cleaning advice was left with the customer; I just hope he passes it onto the next tenant.

Ceramic Tiled Shower Cubicle After Cleaning Herstmonceux

 
 
Source: Stained Ceramic Tiled Shower Cubicle Refreshed in East Sussex

Shower Cubicle Tile and Grout Refreshed in Sale

It’s not unusual for Shower tile and grout to become stained due to the dyes that are found in soap, mould can also be a common problem but usually this is down to inadequate ventilation. Whilst we do sell products that can keep your tile and grout clean we are also able to assist when a really deep clean is required. The photographs below are a great example of this and are of one of three shower cubicles we were asked to clean and restore at a modernised Victorian property in Sale, Cheshire.

Shower cubicle before cleaning in sale Cheshire Shower cubicle before cleaning in sale Cheshire

Cleaning Ceramic Tile and Grout

We started by spraying the tile and grout down with Tile Doctor Pro-Clean which is a strong alkaline cleaner, spraying it on mixes it air which helps it to stick to Vertical surfaces allowing it to get to work on the dirt. We left it to dwell for ten minutes before scrubbing it in by hand using a stiff grout brush; this process certainly improved the grout but unfortunately it had become too badly stained to be satisfactory so we decided to recolour the grout using a white grout colourant.

To get the wall tiles and shower glass clean we sprayed on Tile Doctor Oxy-Pro, again leaving it to dwell for a while before gently scrubbing it away with water. Once dry we set about stripping off the silicone strip around the base of the shower wall which was stained and impossible to get clean again.

Recolouring Grout

The grout colourant comes in a tube and is very straightforward to apply although I must admit the work is quite tedious. Two coats of white colourant were required to get the uniform appearance needed and I think you will agree the effect is quite transforming. The other advantage of these particular colourant products is that they are epoxy based and form a barrier of the grout preventing future staining and making it very easy to clean going forward.

The last step was to apply new silicone along the base of the cubicle and give the tiles a quick buff.

Shower cubicle after cleaning in sale Cheshire Shower cubicle after cleaning in sale Cheshire

I think you will agree it was quite a transformation and the cubicle now looks like it was recently installed.
 
 
Source: Restoring the Appearance of Shower Cubicles in Cheshire

Quick and Effective Bath Tile Refresh in Edinburgh

Here’s a quick example of an interesting tiled shower cubicle at a property in Edinburgh that was well overdue for a refresh, including deep cleaning and recolouring do the grout lines that had become stained and mouldy. This is a problem that the majority of property owners experience due to the simple fact that shower cubicles come into contact with damaging acid-based shampoos and soaps on a daily basis.

The short-term solution for this is to wash the shower cubicle down with water after each use, however busy people do not always remember to do so! The prognosis is bad discolouration, mould growth and staining if the problem if proper care isn’t taken. In this case, the problem had worsened to the point that the property owner decided to contact Tile a Doctor to provide a thorough refresh of the tiles.

Edinburgh bathroom before grout refresh Edinburgh bathroom before grout refresh

Cleaning Stained and Discoloured Shower Cubicle Tiles

Our process for refreshing shower cubicles in a similar state to this one is simple, but highly effective. I started by mixing a strong solution of our high alkaline cleaner, known as Tile Doctor Pro Clean (diluted to an appropriate level with water), before applying it directly to the tile and grout.

Next, I worked it in using specialised handheld grout brushes , with the alkaline in the Pro Clean neutralising the acidic staining and mould growth had leaving the area clean and fresh. Pro Clean is suitable for use on all kinds of natural stone, and on both verticals and horizontal surfaces. Once satisfied the grout had been cleaned to the best of my abilities, I quickly dried the entire area using a heat gun.

Recolouring Shower Cubicle Grout

To restore the appearance of the installation back to it’s optimal appearance I chose to recolour the grout lines with our Light Grey grout colourant, which matched in very nicely. This is just one of ten different colours of grout colourant we offer. The colourant was left to dry for a short period before I cleaned off any excess. The final stage of the refresh involved stripping off the old discoloured silicone from around the bath and replacing it with fresh silicone.

Edinburgh bathroom before grout refresh Edinburgh bathroom before grout refresh

The customer was very impressed by the speed and efficiency of the refresh. With the work completed to a high standard in just a few hours, she now has one less problem to worry about – and a very smart looking shower cubicle! Another satisfied customer.
 
 
Source: Bathroom Tile and Grout Restoration in Edinburgh

Acid-Damaged Slate Shower Tiles Restored with Burnishing in Churt

One problem we encounter a lot at Tile Doctor is damaged caused to natural stone tiles by unsuitable household cleaning products. This customer, who lives in the small West Surrey village of Churt, had done this by attempting to use Cilit Bang, which is an acidic product, to remove limescale from his fantastic Slate tiled shower cubicle. While the product may indeed remove Limescale, it does say on the label that it should not be used on natural stone.

Slate shower before cleaning Churt Slate shower before cleaning Churt

Putting these types of products in contact with acid-sensitive stone typically results in some sort of etching, however, I had never before seen the type of damage that had occurred on these Slate tiles. At first, I thought the damage – which appeared as a sort of white staining – might simply be damage to the sealer. But when I did a test clean to remove the sealer, it became clear that the stone had suffered from very deep staining and the only way to remove it would be to use a process we call burnishing.

Slate shower before cleaning Churt

Burnishing an Acid-Damaged Slate Tiled Shower Cubicle

The burnishing process is a type of polishing which involves the application of diamond burnishing pads in sequence. Each pad has a different level of grit, allowing for dirt and stains to be broken down before the stone is gradually polished. We typically use burnishing on Limestone, Marble, and Travertine, but it can be used on all manner of stone in the right circumstances. This being a vertical surface, I had to complete the process using smaller six-inch pads fitted to a handheld buffer.

I started by applying the 400 grit (Coarse) pad, and followed on through to the 800 grit (Medium) and 1500 grit (Fine) pads, using a small amount of water as lubrication. I then left the tiles to dry until the next day.

When I arrived back at the property, the customer remarked that the tiles looked massively improved. Nonetheless, I found I hadn’t removed all the staining possible, so decided to repeat the burnishing process once – but this time used the pads without any lubrication. Once I was satisfied with the results, it was time to seal the tiles.

Sealing a Slate Tiled Shower Cubicle

My choice of sealer was Tile Doctor Colour Grow, which impregnates the stone to block ingrained dirt and staining. As the name of the product suggests, it also enhances the dark natural shades in the Slate, giving the shower cubicle a bold, healthy and rich appearance.

Slate shower after burnishing Churt Slate shower after burnishing Churt

The customer was really pleased with the end result, which can be seen in the photographs above and below. So pleased was the customer, in fact, that he asked me to quote for the restoration of his Limestone tiled patio.

Slate shower after burnishing Churt

 
 
Source: Restoring the Appearance of Black Slate Tiles in a Surrey Shower Cubicle

Ceramic Tiled Bath and Shower Tiles Refreshed in Hale Village

We commonly encounter customers who are struggling to keep their Ceramic tiled shower cubicles clean. Since most people use their showers every day, the tiles and grout inevitably come into contact with shampoos and soaps that can cause staining, discolouration and mould. In fact, it’s not uncommon for property owners to completely give up on trying to clean the tiles, especially as many everyday cleaners are ineffectual, and this allows the situation to worsen over time.

This customer, who lives in Hale Village – known to be one of the UK’s quietest and best kept villages despite being just outside the busy city of Liverpool – was fed up with the state of her tiled shower cubicle and decided to seek professional assistance. I explained that with regular maintenance using suitable products, the tiles could be easily kept clean. I visited the property to show her first hand the results that could be achieved by cleaning and recolouring the grout.

Ceramic bath tiles before refresh Hale Village Ceramic bath tiles before refresh Hale Village

Grout Cleaning and Recolouring Ceramic Bathroom Tiles

The ideal product for cleaning grout that has become affected by mould is Tile Doctor Mould Away, a fast and effective formula that can be directly applied. After applying the Mould Away I allowed it to soak into the grout for 20 minutes, before scrubbing it in with a special handheld brush. I also scrubbed it into the tiles to remove any excess staining caused by coming into contact with shampoos and soaps.

After completing a thorough clean of both the grout and tiles, it was time to remove the old silicone sealant from around the edges of the bath, and replace it with a fresh white sealant. I then opted to recolour the grout to match it with the tiles and the new sealant, doing so carefully with Tile Doctor’s own White Grout Colourant. This is just one of ten different Grout Colourant options we offer. Other options include Charcoal Grey, Black and Cappuccino Brown to much different colour tiles.

Ceramic bath tiles after refresh Hale Village Ceramic bath tiles after refresh Hale Village

The combination of cleaning and recolouring completely refreshed the appearance of this Ceramic tiled shower cubicle, to the point that it almost looks new. Needless to say my customer was very happy, and can see now just how easy it can be to keep these tiles looking good using the right products.
 
 

Professional Bathroom Tile and Grout Cleaning in Cheshire

Dealing with Mould on Grout and Silicone in Northampton

A common problem with bathroom and shower cubicle tiles is the appearance of mould on the tile, grout and silicone which if not tackled on a regular basis will spread and threaten to severely damage the appearance of the tiles, along with the silicone. This problem is usually due to inadequate ventilation however the good news is that with early intervention with Tile Doctor Mould Away spray the problem can be reversed.

The two photos below show a bad case of this very problem at a property in Northampton, where you can see that the grout and silicone sealant had become black with mould.

Mouldy shower cubicle before Northampton Mouldy shower cubicle before Northampton

Cleaning and Repairing Damaged Shower Cubicle Grout

Firstly, I decided to cut out the damaged grout with a hand held disc cutter and remove all the silicone at the base of the shower. To treat the less invasive mould in the rest of the cubicle I sprayed it with Tile Doctor Mould Away, which is specifically designed to remove mould from silicone and grout.

I sprayed the product onto the affected areas and left it to dwell for five minutes, before scrubbing it in with a stiff grout brush, resulting in a good clean. The area was then rinsed with plain water. Finally, I replaced the grout and the silicone that I had removed earlier with a flexible grout and a white silicone, both of which include a mould inhibitor.

Mouldy shower cubicle after Northampton Mouldy shower cubicle after Northampton

The photographs above show the end result. The customer was very happy with her refreshed tiles, and left the following feedback:

“Phil was brilliant – both when he came to look at the job and then when he returned to actually make the grout repairs. Most importantly he explained what was (and wasn’t possible) and did exactly what he said he would do. My shower area now looks brilliant and I’m no longer showering in fear of the tiles falling off the wall! Honest, clean, timely and totally professional. A tremendous job well done. Thank you.”

I left the customer with a bottle of Tile Doctor Aqua Pro to aid with regular cleaning. If used once or twice a week, this product will help maintain the condition of the grout. I also advised the customer that it is good practice to rinse the tiles down with plain water using the shower head after each shower to remove any soapy residue which can slowly discolour and stain grout over time.
 
 
Source: Shower Tile Cleaning and Maintenance Service in Northamptonshire

Badly Stained and Mouldy Marble Shower a Cubicle Transformed in Beddau

Tiled shower cubicles can very easily become tired and grubby looking without the right care. The shampoos and soaps we use in our everyday lives can have long lasting damage if their effects are not sufficiently dealt with, with grout mould being a very common problem for property owners in the UK where we have a cold climate that encourages us to seal up our homes limiting natural ventilation.

Marble Shower Enclosure Tiles Before Cleaning in Beddau

At this property in the small village of Beddau, near Cardiff, my customer had a particularly poorly maintained Marble tiled shower cubicle suffering from bad staining. Since Marble is an acid-sensitive stone it is especially vulnerable to damage when exposed to even slightly acidic shower products. The grout was also in a bad way, having turned from a pleasant off white colour to black. The entire area was now well overdue from some attention from the Tile Doctor.

Marble Shower Enclosure Tiles Before Cleaning in Beddau

Cleaning a Marble Tiled Shower Cubicle

To begin the restoration of these tiles I had to remove any old sealer. I did this by applying a combination of Tile Doctor Pro Clean, which is a versatile cleaner, stripper and degreaser, and Tile Doctor NanoTech HBU, which is a more powerful product designed for the removal of heavy soil buildup.

As the old sealer came away, I left the two products to soak into the tiles to lift out the stains and ingrained dirt caused by the Marble’s exposure to shampoo and soaps. This really helped to alleviate the grubby appearance previously held by the tiles.

As previously mentioned, the grout lines were also in a really bad state. Undeterred, I attempted for three hours to clean the grout lines with unsatisfactory results, and so resolved instead to remove the old grout entirely and re-grout with a new Jasmine coloured grout throughout the bathroom. I did consider simply recolouring the grout with one of our Grout Colourants but, as an experienced tiler, I felt for me it would quicker and easier to achieve the required results by re-grouting.

Marble Shower Enclosure Tiles During Cleaning in Beddau

Sealing a Marble Tiled Shower Cubicle

After leaving the grout and tiles to dry overnight following the cleaning and regrouping, I returned to the property to seal the area. To do this I opted to use two coats of Tile Doctor Colour Grow, our solvent-based impregnating sealer which fills the pores of the stone to act as a barrier against trapped dirt and stains, and to prevent further contamination.

As a colour intensifying sealer it really emphasised the natural shades in the Marble. Colour Grow can achieve similar results on other types of unpolished stone, including Limestone, Flagstones, Quarry, Sandstone and Slate.

Marble Shower Enclosure Tiles After Cleaning in Beddau

I added the finishing touches to the restoration by removing all the mouldy silicone and replaced it with new silicone. Though this wasn’t the easiest of jobs, the final result is one of which I am particularly proud. It certainly pleased the customer!

Marble Shower Enclosure Tiles After Cleaning in Beddau

 
 
Source: Marble Tiled Shower Cubicle Professionally Refinished in South Wales

Deep Cleaning a Dirty Shower Cubicle in Middlesbrough

Here’s a fairly straightforward job I completed at a house in Middlesbrough which if you haven’t come across it before is a large industrial town situated on the south bank of the River Tees famous for its football club.

My client was keen to have the Ceramic tiled shower cubicle in her bathroom refreshed, paying particular attention the areas where the tiles and grout had been stained by the chemicals in shampoos and soaps. There was also signs of mould build-up that needed to be addressed.

Ceramic Shower Tiles Middlesbrough Before

Cleaning a ceramic tiled shower cubicle

My first task was to mix a strong solution of Tile Doctor Pro-Clean and clean water. Pro-Clean is an alkaline-based cleaner that is highly effective for removing grease, soap scum, and more. While in this case I used Pro-Clean to clean the Ceramic wall tile and grout, it is also suitable for use on most natural stone floor tiles, including Granite, Slate, Limestone and Travertine.

I then decanted the solution into a spray bottle, and applied it to the tiles and grout. The reason for using a spray bottle is due to the fact cleaning products generally don’t stick very well when applied directly to vertical surfaces. When applied via a spray bottle the solution is mixed with air, turning it into more of a vapour which clings more effectively to the surface.

After the solution had been applied, I left it to dwell for a while before scrubbing it into the tiles and grout. As you can see from the photos, this made a big difference breaking down the mould and soap scum and I was soon able to wash away the resultant slurry leaving an inviting shower cubicle.

The final step was to replace the silicone sealant strip between the shower tray and the tiles; the silicone strip is not so easy to clean and although applying fresh silicone can be tricky it does finish the job off rather nicely. As an alternative you can apply Tile Doctor Mould-Away which does work on Silicone however if your shower is leaking then you can almost guarantee it’s the silicone strip that’s the cause.

Ceramic Shower Tiles Middlesbrough After

If the shower wall had been made from stone I would now be talking about sealing the tiles however Ceramic tiles are glazed and won’t take a seal so the only consideration would have been to use a Grout Sealer however in this case we didn’t feel it was necessary. The shower cubicle now looks like a new installation and my customer was very pleased with the transformation.
 
 
Source: Professional Tile, Stone and Grout cleaning and maintenance services in Teesside

Dealing With Limescale On Polished Stone

I recently went the assistance of a home owner in Addlestone, Surrey who had damaged the surface of the Marble tiles in her shower by attempting to remove Limescale using a well-known household cleaning product, which unfortunately due to its acidic formula actually made the problem worse and etched the tiles.

Limescale on Marble Shower Tiles Addlestone

Burnishing Marble Shower Cubicle Tiles

To remove the etching and Limescale from the Marble tiles the surface would need to be cut back and re-polished using diamond encrusted burnishing pads. For this job we used a set of six inch pads which are similar to the floor pads but smaller so they can be attached to a hand held machine and used on vertical surfaces.

To burnish the tiles a coarse pad is applied first lubricated with a little water and this removes surface deposits such as Limescale and in this case also the etching. The resultant residue is washed away and then you proceed on with the Medium, Fine and Very Fine polishing pads until the surface has been restored.

Sealing Marble Shower Tiles

Once I had finished applying the Very Fine pad I gave the tiles a thorough rinse and then dried them so they could be sealed for which I used a coat of Tile Doctor Colour Grow which is an impregnating sealer that gets into the pores of the stone enhancing the natural colours in the process.

Limescale removed from Marble Shower Tiles Addlestone
The owner was really grateful because she was thinking that they would need to be replaced which as you can imagine would have been very expensive.
 
 
Source: Professional Shower Tile, Stone and Grout cleaning and maintenance services in Surrey

Cleaning Up a Grubby Shower Cubicle in Bishopton

This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the look without the expense.

Gruby Ceramic Tiled Shower in Bishopton Before Gruby Ceramic Tiled Shower in Bishopton Before

Cleaning Ceramic Tile and Grout

We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning showers. The spray delivery is important as mixing the cleaning product with air makes it lighter and helps it cling to the tile and grout. The Oxy-Pro was left to soak into the tiles for around 15 minutes before being scrubbed into the tile and grout using a stiff grout brush. This action cleaned up the grout and tile nicely removing stains from shampoos and soaps etc.

Removing Mould from Grout

The grout was looking much improved but there was however some evidence of mould remaining which needed dealing with. To tackle this we used Tile Doctor Mould Away which is designed to remove mould off Silicone and Grout. It’s very easy to use, you simply spray the Silicone or Grout to be treated with Mould Away then leave to soak in for five minutes and then scrub with a brush and rinse with water repeating the process until the mould has disappeared.

Gruby Ceramic Tiled Shower in Bishopton After Gruby Ceramic Tiled Shower in Bishopton After

It took a fair amount of manual effort but the results were well worth it as you can see.
 
 
Source: Professional Shower Tile, Stone and Grout cleaning and maintenance services in Glasgow

Marble Tiled Wet Room in Great Bricett, Suffolk

Details below of a wet room lined with 10m2 of Marble in old cottage on the outskirts of the medieval village of Great Bricett in the heart of Suffolk. You can see from the photographs staining of the Marble Tiled wall and floor which was left in a mess after a friend of the family had tried to remove the limescale during a visit.

Marble Shower Cubicle Before Cleaning Marble Shower Cubicle Before Cleaning

Cleaning and Sealing Marble Tile

The Marble tiles were cleaned and polished using a set of mini Twister burnishing pads. The pads are encrusted in diamonds are brilliant at restoring hard stone surfaces such as Marble. You start with the red pad to remove the existing sealer followed by the white and yellow pads to clean and hone the stone. The wall and floor tiles were then rinsed with water to clean and neutralise the floor ready for sealing.

The room had under floor heating which helped to dry out the tile and so it was soon possible to use the final green pad to polish the tiles and move onto sealing. To seal we used two coats of Tile Doctor Colour Grow which is a colour intensifying breathable sealer that enhances colour as well as providing durable surface protection, a one litre bottle of sealer was sufficient.

Thanks to the under floor heating we managed to complete the job in a single day and as you can see from the final set of photographs below the stains have been removed and the tiles restored to their original appearance.

Marble Shower Cubicle After Cleaning Marble Shower Cubicle After Cleaning

 
Source: Limescale removed from Marble Tiled Shower in Suffolk