Restoring Limestone Tiles Damaged by a Cleaner in Huntingdon, Cambridge

I was recently asked to take a look at a Limestone tiled shower cubicle at a house in the market town of Huntingdon. It turns out a cleaning company had tried to clean the tiles with an acidic product which was unsuitable for a calcium stone. I suspect they used a limescale remover which is very acidic. The owner was horrified by the damage that had been caused which as you can see from the pictures had ruined the appearance of the stone.

Etched Limestone Tiled Shower Before Renovation Huntingdon Etched Limestone Tiled Shower Before Renovation Huntingdon

Always check the label before applying an unfamiliar product to natural stone as most household and commercial cleaning products are simply not suitable. It is essential that the correct product is used and if in doubt talk to Tile Doctor who have a product for everything related to maintaining stone.

I discussed with the client what needed to be done to rectify the job. They were happy with my quote and were relieved that their Limestone tiles could be salvaged.

Renovating Damaged Limestone Shower Tiles

With the extent of the damage, most of the work to rectify was to be done by hand. I started by applying a set of handheld diamond blocks to cut back the stone to remove the etching. This was then followed up with a set of small diamond encrusted burnishing pads. The pads are applied to the Limestone tiles in sequence using a handheld buffer with water for lubrication. The sequence runs from coarse to very fine and we rinsed with water between each pad to remove the soil.

With a lot of man hours and elbow grease later, we had corrected the damage caused.

Sealing Limestone Shower Tiles

Once the stone had dried, I moved onto sealing the Limestone to prevent dirt and other stains from shampoo dyes affecting the stone going forward. To do this I applied several coats of Tile Doctor Ultra Seal, this is an impregnating sealer that seeps into the pores of the stone leaving a natural look yet leaving a delicate sheen. As you can see from the pictures the results were dramatic and very successful.

Etched Limestone Tiled Shower After Renovation Huntingdon Etched Limestone Tiled Shower After Renovation Huntingdon

The client was impressed with the transformation I had managed to achieve and left the following feedback for me.

“Tom was punctual on both the day he quoted and on the day he arrived to undertake the work. He was also very mindful of our semi house cats and made sure he did not let them out. That sounds simple but of the many tradesmen we have had around in the last six months for restorative work on the house he was one of a couple that did not need constant reminding. The work he undertook was to rectify, as he put it, “some of the worst damage to tiles I have seen to date”! The tiles were limestone and had been badly marked by an acid based cleaner. By the end of five solid hours work he had got the tiles back to looking brand new with not a mark to be seen. He did so with no mess, a very cheerful disposition and several cups of coffee! I would not hesitate to recommend Tom to all my own clients and friends” Bob H, Huntingdon

 

Source: Damaged Limestone Shower Tile Renovation in Huntingdon, Cambridge

Renovating Mouldy Travertine Shower Tiles in Sheffield

I was asked to call into a property in the Sheffield suburb of Totley to renovate a troublesome Travertine tiled shower enclosure. The customer simply couldn’t keep the shower clean and the travertine was just getting dirtier and dirtier. I could see from the pictures that the stone tiles were becoming stained with the use of shampoo and soaps, also there was evidence of mould build-up which had led to some of the grout turning black.

Once I was on site, I could see that any sealant that may have been present on the Travertine had broken down and worn off leaving the pores in the stone vulnerable to dirt etc. Once dirt has become ingrained you will find it very difficult to get rid of it using normal household cleaners. I discussed with the client the best course of action, we chatted about the cost and they were happy to go ahead with the work. The work would take less than a day to complete.

Travertine Tiled Shower Enclosure Before Cleaning Totley

Cleaning a Travertine Tiled Shower Enclosure

I started by applying Tile Doctors Oxy-Gel which is a Tile and Grout cleaning product in a Gel form that allows it to cling to walls without running off. This means you can leave it working on the Tile and Grout for as long as you want. Thirty minutes is normally enough to clean most stone and lift the underlying dirt. The Oxy-Gel was then scrubbed in by hand and rinsed off with water. The first clean, removed most of the dirt and grime, however the really stained areas were treated twice.

Once the stone was clean, I turned my attention to the mould stained silicone seal between the tile and shower tray. I worked carefully to remove the existing silicone with a sharp knife to ensure neither the tile or shower tray was damaged. After cleaning up the area and making sure it was dry new Limestone coloured silicone was inserted to match the grout. It’s important to use good quality silicone as the cheaper ones tend to discolour fast.

Sealing a Travertine Tiled Shower

Once the tiles were fully dry, I set about sealing the Travertine and Grout using two coats of Tile Doctor Ultra Seal. This is a premium, no-sheen, natural-look, sealer which is formulated to provide maximum stain protection, it is also an excellent grout sealer. The natural colours of the now clean Travertine tiles were able to shine through and any water now runs off the wall instead of collecting in the pores of the stone.

Travertine Tiled Shower Enclosure After Cleaning Totley

As you can imagine my client was delighted with the result. To ensure they stopped using the household cleaners applied previously we left them with some free Tile Doctor Aqua-Pro shower cleaner and instruction on how to keep the shower area looking great. This product is pH neutral so will not prematurely erode the sealer which happens with stronger supermarket products.

 

Source: Travertine Tile Cleaning, Restoration and Sealing Service in South Yorkshire

Polishing Black Marble Shower Tiles back to health in Oxfordshire

I received a call regarding a Black Marble tiled shower that the customer thought he would clean himself and ended up unfortunately making worse. Black Marble adds a very opulent and elegant look to a bathroom, and I suspect this particular variety with the white veins is known as “Negro Marquina” which comes from the Basque region of Spain. I did a quick price check on-line and these tiles are priced around £60 each!

Black Negro Marquina Marble Shower Tiles Before Polishing Thame

If you look closely at the before picture you can see the Marble has lost its shine and has a cloudy appearance. This was due to the use of an acid based cleaner. Thame and Oxford lie in a hard water area, so we often find customers seek to remove Limescale deposits off tile using household products such as Vikal or Cillit Bang. The trouble with these products is they are acidic, and marble is acid sensitive so is easily marked and damaged by their use. You should always read the label before using any cleaner to check if its safe to use on natural stone.

The client was desperate to get the shower room looking how it should when he had selected this beautiful stone.

Cleaning a Marble Tiled Shower

To rectify the problem and restore the polished appearance of the marble I burnished the stone using a small 6 inch 200-grit diamond pad attached to a handheld buffer. This coarse pad cuts back the stone surface to remove the etching, I then used a 400-grit pad which removed the fine scratches made by the first pad. This was followed up with an 800-grit pad which starts the honing process which restores the polished appearance. Water is used to lubricate the process and the tiles are rinsed with water after each stage to remove the fine slurry that is generated.

This is further followed by 1500 and 3000 grit pads the last pad is applied dry with only a little bit of water and leaves the tiles dry and ready for the next stage.

Polishing a Marble Tiled Shower

To further build the polish and protect the stone I applied Tile Doctor Shine Powder buffed in with a white pad. This was applied to the marble wall tiles and then rinsed with water and wiped dry with a clean cloth. When the tiles were fully dry, I buffed the tiles with a clean white pad to show the final polished finish. The tiles looked much improved and very shiny.

Black Negro Marquina Marble Shower Tiles After Polishing Thame

The job was completed in a day and the customer was much relieved that I was able to restore the appearance of the marble. I suggested that he should use Tile Doctor Aqua Pro as his tile cleaner of choice in future. This is pH neutral so will not damage the tiles like the acidic products he had used previously, and it should help him keep the shower room looking sparkling and opulent as initially intended!

 

Source: Marble Tile Cleaning, Polishing and Sealing Service in Oxfordshire

Renovating a Grubby Shower Cubicle in Manchester

Shower Tile and Grout renovation is a speciality of ours and has made us popular with landlords who understand properties are easier to rent when the bathrooms look fresh. This was the case with this shower cubicle at a rental property in Chorlton-cum-Hardy which is a popular suburb of Manchester south of Old Trafford.

Grubby Shower Cubicle Before Renovation Chorlton Cum Hardy Rental Property

The shower cubicle was in quite a state and well overdue a deep clean. You can see from the photographs that the shower tray was very dirty, the white ceramic wall tiles were grubby, the white grout had gone black and the silicone sealant had darkened with mould.

Grubby Shower Cubicle Before Renovation Chorlton Cum Hardy Rental Property

Cleaning a Grubby Shower Cubicle in Chorlton

Working in sections from top to bottom I began the cleaning process by treating the tile and grout with Tile Doctor Duo-Clean which a double action cleaning product. Duo-Clean is a recent addition to the Tile Doctor range and combines the properties of an effective tile and grout cleaner with a mould remover. It cleans and can remove mould and blackspot from grout and silicone, so an ideal product for cleaning up neglected shower cubicles.

The spray attachment mixes the product with air making it light and allowing it to easily stick to vertical surfaces where it can get to work breaking down dirt and mould. It was sprayed onto the wall tile and grout and then left to dwell for five minutes before being scrubbed in with a stiff brush. The area was subsequently rinsed with water to remove the soil. In some stubborn places, I didn’t achieve the desired result right away, so I repeated the cleaning process a couple of times before moving onto the next section. I can tell you a lot of elbow grease was expended on this particular cubicle, I even cleaned up the shower tray which had gone green with an accumulation of soap scum.

When the tile and grout was cleaned to the best of my abilities, I used a heat gun to dry the walls quickly. Next, I removed all the mouldy silicone around the shower tray with a sharp knife and then further dried the area.

Sealing Shower Grout

After everything was cleaned and dried, I sealed the grout using Tile Doctor Wall Tile and Grout Sealer Aerosol Spray. The tiles were glazed ceramic so won’t accept a sealer however the top layer of grout is porous which makes it vulnerable to dirt, grease, mould and limescale. Sealing will therefore ensure it keeps its appearance for longer and reduce the need for regular maintenance. Being a spray on sealer it’s very easy to apply, all you have to do is wipe it off the excess sealer from the adjacent tile afterwards.

Grubby Shower Cubicle After Renovation Chorlton Cum Hardy Rental Property

When I had finished sealing the grout, I applied new, high quality and mould resistant silicone in White to match the tile and shower tray. With that, the restoration was complete.

The whole process took less than a day and although it was hard work both myself and the landlord were very pleased with the outcome. If you didn’t know any better, you would think it was a brand-new installation.

Grubby Shower Cubicle After Renovation Chorlton Cum Hardy Rental Property

 

Source: Shower Cubicle Cleaning in Greater Manchester

Darkening Light Grey Grout in a Surrey Bathroom

This client is a famous artist who has just had a new house built inCobham. The house is stunning, and the design details have had a lot of thought put into them. As with big projects such as these there are lots of things to think about and to ensure the builders deliver your vision and artists do have an eye for detail.

A point of contention was one of the bathrooms where the tiler had used a light grey grout in the shower and a dark grey colour in the rest of the bathroom. Although an interesting contrast It looked rather odd and my client was not keen on it nor was it made clear as to why it had been grouted in that colour.

Porcelain Tiled Bathroom Before Grout Colouring Cobham

The brief was to have dark grey in the whole bathroom! As is her right after spending a lot of money, she wanted uniformity, but the tiler wasn’t having any of it. She was rather fed up with the whole situation so contacted us at Tile Doctor to ask if we could rectify the problem. In fact, this is a relatively easy job to solve so I discussed the solution and how long it would take and provided a quote for doing the work. She was happy to agree to my quote and I arranged to return the following week.

She was keen to get all the works completed and tie up all the final snags. Cobham is a very desirable area of Surrey and she will be in good company with many celebrity neighbours nearby. The high street is also full of lovely shops and restaurants, unfortunately no time for me to stop.

Grout Recolouring a Porcelain Tiled Bathroom Walls

To resolve the issue, I applied a Tile Doctor Grout Colourant in Charcoal Grey to all the wall grout in the bathroom to ensure uniformity. Tile Doctor Grout Colourant dries very quickly so once applied any excess must be removed quickly, I recommend wet wipes for this. This product is equally effective for interior or exterior applications including all types of bathrooms and kitchens and is available in ten different colours making it very versatile. It is easy to apply but ensuring the excess is removed is the key to a good finish.

Five hours of effort, one bottle of Tile Doctor Charcoal Grey Grout Colourant and three packets of wet wipes later and the job was finished. Whilst it is a simple job, it is quite time consuming and a little patience is required. However, I have to agree with the owner, the bathroom looks much more sophisticated with a darker grout colour, it’s amazing how a subtle change can make such a difference. It is worth noting when you have any tiling done, there is a variety of colours of grout available so always ask the tiler, don’t just assume there is one choice.

Porcelain Tiled Bathroom After Grout Colouring Cobham

The client was now satisfied, and the bathroom looked how she had envisaged it. I must admit, the light and dark grey combination really didn’t work! I took the opportunity to suggest she should use Tile Doctor Oxy-Pro spray for regular bathroom tile and grout cleaning as she has several tiled bathrooms in the new house, and this will ensure they remain in pristine condition.

 

Source: Grout Cleaning, Colouring and Sealing Service in Cobham, West-Surrey

Renovating a Ceramic Tiled Bathroom in Manchester Apartment

A client with a high-rise apartment in Manchester city centre contacted us in relation to the look of their bathroom tiles. The grout had become grubby and black with mould and it was clear from their message that they were considering have the grout replaced in order to freshen up the bathroom.

We discussed the problem over the telephone, and they emailed a picture of the bathroom across so I could get a better idea of what needed doing. It turns out that the apartment had been rented out previously and they needed the bathroom renovating so they could start letting it again. Clearly, they were keen to have the work completed as soon as possible. Fortunately, we are sometimes able to come out on short notice, especially for small jobs like this and so were able to do the work the following week

Manchester Rental Apartment Bathroom Before Grout Colouring

Re-grouting is a lot of work and very time consuming so I explained the benefits of Grout Colouring which is much quicker and results in a more practical finish as I will explain. There was a small issue with parking as one would expect from the city centre, but we were able to use one of the parking spaces of a neighbour in the basement of the building.

Cleaning the Grout and Tiles in a Ceramic Tiled Bathroom

My first task was to get the grout as clean as possible before applying the colourant and given the amount of mould I decided to apply Tile Doctor Duo-Clean which is a Tile Cleaner/Mould Remover and ideal for use on ceramic tile and grout. The product was sprayed onto the tiles and grout and then scrubbed in by hand to get the grout as clean as possible. I also used a powerful steam cleaner to get the grout as clean as possible before rinsing the soil off with water. This process went well, and the grout looked much cleaner afterwards but was now a little patchy in places due to deep staining.

It’s worth noting that mould thrives in damp warm conditions and can easily be controlled by ensuring the bathroom has adequate ventilation. Some modern showers have a function that cool the bathroom down after use by running the shower on a cold setting. Improving cross-ventilation by leaving the bathroom door and a window open can also improve the situation and of course you can always apply Tile Doctor Duo-Clean on a regular basis.

Recolouring Grout in a Ceramic Tiled Bathroom

Once the grout was dry and as clean as it could be, I applied a White Tile Doctor Grout Colourant along the grout lines with a small brush taking care to wipe off any excess from the tiles as I went. Only one bottle of colourant was needed, and I have found baby wipes work well when wiping off the excess.

The last step in the bathroom renovation was to strip out all the old mouldy silicone between the bath and the tiles and replace with new mould resistant silicone.

The cleaning and grout colour completely transformed the look of the bathroom leaving it looking fresh. The grout which was previously dark and patchy was now a consistent white colour giving the impression it had only been recently tiled. The colourant also forms an epoxy barrier over the grout that will prevent dirt from becoming ingrained in the grouts surface going forward, it’s also much easier to clean.

Manchester Rental Apartment Bathroom After Grout Colouring

The customer was most impressed with the result and has informed us since that they will back in touch about renovating the grout in their own home! They left the following comment on the Tile Doctor website.

“Kamila made a wonderful job cleaning my grout and silicone. The bathroom looks like new. She was also easy to deal, very friendly and professional. Thank you!”

 

Source: Ceramic Tile and Grout Cleaning and Restoration Service in Manchester

Renovating a Mouldy Travertine Tiled Shower in Abingdon, Oxfordshire

This shower cubicle at a house in the historic market town of Abingdon on Thames was tiled with Travertine which with use had become grubby and the grout darkened. The properties in the road were of a similar age and many bathrooms had been upgraded in recent years to make them more modern. This one was no different having been fitted a few years prior.

Travertine Tiled Shower Before Cleaning Abingdon

Travertine is a natural stone material that has unique features and colouring that no other stone can offer. The distinctive design and natural patterns found within Travertine make it very popular choice in bathrooms, where it gives a luxury hotel style feel. It does however need to be maintained if you want it keep that luxury appearance and unfortunately due to the English climate and a general lack of adequate ventilation its quite common for them to attract mould and become stained with dyes from soaps and shampoos. The good news is we have a number of tools and products that we can use to restore their appearance, so they look like a new installation.

Deep Cleaning Travertine Shower Tiles

The main problem was the grout which was badly discoloured. To tackle this the Travertine and grout was sprayed with Tile Doctor Duo Clean and then scrubbed in with a hand brush to remove the mould and ground in dirt from the grout, I then rinsed with water. Duo Clean is a fast and effective double action grout cleaner and mould remover. It cleans up grout and can also remove mould and blackspot from the grout and silicone and it is versatile as it suitable for use on plastic and enamel baths and showers and will not cause any damage to them.

To restore the appearance of the stone I set about re-honing the Travertine tiles using six-inch diamond burnishing pads fitted to a hand buffer. The pads are applied in sequence starting with 400-grit, moving onto 800-grit and finishing with 1500-grit. Applied with water which acts as a lubricant, the process deep cleans and tightens the pores in the stone to improve overall appearance. The tiles are rinsed with water after each pad is applied to remove the soil that is generated.

Sealing a Travertine Tiled Shower Room

Another issue was the silicone strip between the wall tiles and the shower tray which was looking very mouldy and black. Using a sharp knife this was removed and replaced with fresh white mould resistant silicone.

Once the shower area was dry the Travertine wall tile and grout were then sealed with a couple of coats of Tile Doctor Colour Grow. This adds a preventative barrier over the tile and grout allowing water to easily run down the wall, it also improved the appearance of the stone and enhanced the natural brown colours in the Travertine. The customer was very happy with the shower room, it looked much more inviting and they were surprised that I had managed to restore it to the way it looked when it was originally installed.

Travertine Tiled Shower Before Cleaning Abingdon

 

Source: Travertine Tile Cleaning and Sealing Service in Abingdon, Oxfordshire

Limescale and Mould Removed from Limestone Wet Room in Reading, Berkshire

This enquiry came from a theatre buff at a house in Sonning Eye near Reading who regularly hosted cast members playing at the local Mill Theatre. Five years prior he had a Limestone tiled wet room installed and unfortunately the floor tiles were laid unevenly and the fall on the tiles didn’t allow the water to drain off efficiently. The water would therefore tend to pool in the centre and overtime heavy limescale built-up and mould had also started to appear.

Limestone Shower Before Renovation Sonning Eye

Cast members staying at his house although grateful of the hospitality had often mention the state of the unsightly shower and so we were asked to pop round and see what could be done to renovate it and restore its appearance.

Shower Tile and Grout Cleaning

The first task was to remove the mould that had ingrained the Limestone, to do this I used Tile Doctor Duo Clean and scrubbed it into the tile with assistance from a steamer. I repeated this action three times, after each time I could see a visible improvement in the affected area and once it had lightened to a very faint grey, I knew that the next cleaning process to burnish the stone would see it disappear completely so left it at that.

Limestone Shower During Renovation Sonning Eye Limestone Shower During Steam Cleaning Sonning Eye

Next job was to remove the limescale build-up and re polish the Limestone tiles. I found the best way to do this was with a small hand-held machine, this allowed me to get into all the edges and groves that would have been impossible with a larger machine which would have struggled to cope with the uneven tiles.

Limestone Shower During Polishing Sonning Eye

I started with a 400-grit burnishing pad, but this struggled to cut into the years limescale build-up, so I switched this for 100-grit soft milling pad which did the trick. Once all the limescale had been removed it was time to rebuild the polish on the surface of the stone, so the process was repeated working through finer and finer burnishing pads 200, 400, 800,1500 and finally 3000-grit until the appearance of the Limestone was restored. This is quite a time-consuming process as the pad are quite small, additionally each pad is applied with water to provide lubrication which turns into a slurry that has to be rinsed off before applying the next pad. The result however is worth at as it really restores the polished appearance of the Limestone.
The last part of the cleaning process was to give the grout a quick clean I did this by scrubbing in Tile Doctor Pro-Clean along the grout lines with a grout brush, again rinsing off the slurry afterwards. Pro-Clean is a strong alkaline tile and grout cleaner that’s safe to use on natural stone.

Sealing Limestone Tiles in a Wet Room

The final task was to seal the Limestone and replace the worn mastic/silicon sealant around the edges. Usually I would leave the stone to dry out overnight but as it was a small area, I was able to thoroughly dry it out using a heat gun. Once dry two good coats of Tile Doctor Ultra-Seal were applied to provide on-going protection. Ultra-Seal is an impregnating sealer that works by occupying the small pores in the stone thereby preventing dirt from becoming ingrained, also it doesn’t change the colour of the stone in any way leaving a very natural appearance.

Last step before finishing was to apply a fresh application of white mastic sealant along the edges of the tiling to ensure a good seal and no leaks.

Limestone Shower After Renovation Sonning Eye

My customer was over the moon with the result as initially he thought he might have to have it replaced. He was so pleased in fact that he left the following feedback on the Tile Doctor feedback system.

“Excellent prompt and courteous service from Dennis who I cannot recommend too highly. After completion of the work a previously very tired looking wet-room looked better than it did when new.”

Limestone Shower After Renovation Sonning Eye

 

Source: Stone Shower Tile Cleaning and Renovation Service in Sonning-Eye

Porcelain Wall Tile & Grout Cleaned of Mould in Osmotherley

The pictures below are of a Porcelain tiled shower cubicle at a property I was asked to survey in the village of Osmotherley on the Western edge of the North York Moors national park. It had been tiled in two different types of Porcelain to achieve an impressive effect. Unfortunately, the tiles had now become discoloured with the usual build-up of soap dyes, soap scum and mould. To make things worse there were layers of silicon sealant that were more black than clear, making it look really dirty and unpleasant.

Mouldy Porcelain Shower Cubicle Before Cleaning Osmotherley

The client had contemplated trying to replace this themselves but recognised they could not achieve a good finish. We discussed the work to be done and agreed a price and a suitable date.

Mouldy Porcelain Shower Cubicle Before Cleaning Osmotherley Mouldy Porcelain Shower Cubicle Before Cleaning Osmotherley

Cleaning a Porcelain Tiled Shower Room

I first spayed the grout with Tile Doctor Pro-Clean in a 1:3 dilution with water to loosen the soap scum. Dependent on the situation and how soiled the tiles we will dilute the product accordingly. This was left to dwell for a short time, scrubbed and rinsed off. I then applied Tile Doctor Oxy-Gel to small 2 square metres areas of tile at a time and left for ten minutes before scrubbing it in to remove the grime. This process was repeated until all the walls were scrubbed down. It was amazing how much dirt and grime was removed. The resultant slurry was then rinsed off thoroughly with water and removed with the wet vacuum.

I then spent nearly four hours carefully removing the layers of silicone sealant, the sealant had been reapplied before on top of the existing by the previous owners. It was a tedious part of the job, but essential to remove all the sealant so we could get a nice finish when we came to reapply it. Also, to make sure there was no moisture trapped between the tile and tray l force dried it with a heat gun.

Sealing a Porcelain Tiled Shower Cubicle

Then a thin coat of quality mould resistant clear silicone was applied to provide a water proof barrier around the edges of the shower cubicle. This ensures that no water can escape from the cubicle and get behind the tiles or worse still leak through the ceiling. It is critical that this is water tight.

Mouldy Porcelain Shower Cubicle After Cleaning Osmotherley Mouldy Porcelain Shower Cubicle After Cleaning Osmotherley

You can see from the pictures a massive transformation in the appearance of the shower, it now looks a lot more inviting and appealing to use!

For aftercare I recommended the use of Tile Doctor Duo Clean which is an effective double action grout cleaner and mould remover designed for use in bathrooms.

Mouldy Porcelain Shower Cubicle After Cleaning Osmotherley

 

Source: Shower Tile Cleaning and Renovation Service in Osmotherley, North West Yorkshire

Removing Limescale from Slate Shower Tiles in in Stevenage

Our client contacted Tile Doctor as they were having problems cleaning their Slate tiled ensuite bathroom. We visited the property in nearby Stevenage, a London commuter town which is between Letchworth Garden City and Welwyn Garden City. The bathroom had been fitted some time ago, but due to the hard water in the area, there had been a large build up of limescale. The dark slate tiles showed this up even more.

Slate Tiled Bathroom EnSuite Stevenage Before Cleaning

My client had tried numerous household products on the tiles, but nothing was shifting the heavy build up. I discussed with them what Tile Doctor could do and completed a small demonstration. They were surprised how easily we were able to improve the tiles. We agreed a price and a timescale and booked the work in for a few weeks’ time.

Cleaning and Restoring a Slate Tiled Ensuite Bathroom

The ensuite shower required intensive cleaning to the shower walls and floor where excessive limescale was present so we got to work cleaning with Tile Doctor Oxy-Gel, this is a strong alkaline based cleaner and degreaser, it is a gel so it works well on vertical surfaces where a long dwell time is required to break down dirt, grime, soap scum, oil based products. We left the product on the surface for approximately 10 minutes, removing all previous sealers and dirt. The residue was rinsed off and followed this up with a second clean using Tile Doctor Grout Clean-Up.

Grout Clean-Up is an acidic product designed to remove mineral deposits however you need to be careful with some types of stone as it can etch the surface if used incorrectly. To apply the product was diluted with water in a spray bottle and sprayed on to the wall tiles where it was scrubbed in and then rinsed off. The process was then repeated on the floor rinsing down thoroughly afterwards with water.

Sealing a Slate Tiled Ensuite Bathroom

Once the slate was clean and dry we proceeded to cut out the existing silicone sealant which was equally stained and was beyond cleaning. This is a slow job and care needs to be taken not to scratch the tiles. It is important to ensure all the old silicone is removed so there is a nice clean surface to reapply the new. This also gave the shower area more time to dry out.

We tested with the moisture meter to ensure the shower area was fully dry and then applied the sealer. We chose to apply three coats of Tile Doctor Colour Grow, this is an impregnating sealer that works by occupying the pores in the stone, so dirt can’t become ingrained there, its also a colour enhancing sealer that provides durable protection. We applied the coats then lightly buffed off the excess with a soft cloth and allowed the slate to dry. The following day we returned to re-silicone all the edges and joints.

Slate Tiled Bathroom EnSuite Stevenage After Cleaning

We recommended to the customer to use a mild solution of Tile Doctor Stone Soap as a maintenance cleaner for the slate. The client was very happy with the result and could see that cleaning with the appropriate product would ensure the ensuite bathroom continued to look good. The whole job took a day and a half to complete.

 

Source: Slate Tile Cleaning and Renovation Service in Stevenage, Hertfordshire

Renovating a Family Shower Cubicle in a Sheffield Suburb

We were contacted by a family from Hillsborough, which is a suburb of Sheffield, who had seen some of the work we do renovating shower cubicles on the internet and wanted to know if I would do the same for their shower.

Ceramic Shower Tile and Grout Before Revamp Sheffield Ceramic Shower Tile and Grout Before Revamp Sheffield

One of the biggest problems affecting bathrooms is mould which thrives in a warm damp environment, the best way to prevent it is to extract the moisture created when having a shower with adequate ventilation. Other steps you can take to reduce mould include always leaving the door open after a shower to improve cross ventilation and rinsing the shower down with cold water afterwards. Tile Doctor also have a product called Aqua-Pro that you can spray on your tiles after use.

I went over to take a look and could see that the Ceramic tiles were only slightly stained and would no doubt clean-up easily however the grout had gone black in places with mould and orange in others due to the dyes in shampoos and soaps. Ceramic tiles are glazed and so usually very easy to keep clean however grout and silicone is more vulnerable and if you now cleaned on a regular basis mould can get a grip and it can prove very stubborn to remove.

Ceramic Shower Tile and Grout Before Revamp Sheffield

Cleaning Ceramic Bathroom Tile and Grout

The home owners had tried to rectify the problem before by applying more grout and silicone to the affected areas however this hadn’t cured the ventilation issue, so it wasn’t long before the problem resurfaced. I recommended replacing all the badly affected grout and the silicone sealer strip around the base of the shower to give the cubicle a fresh look.

My first task was to see how far we could get by cleaning the tile and grout using Tile Doctor Duo-Clean which is designed for use in bathrooms where it’s effective at cleaning grout and removing mould. It comes in a spray bottle so it’s just a question of spraying it onto the tile, grout and silicone and leaving it for ten minutes before scrubbing it in with a stiff brush or scouring pad. The soil was then rinsed off the tile and grout and the shower left to dry off for a while, so we could see which areas were so badly stained would need re-grouting.

The next step was to carefully remove the old silicone sealant from around the edges of the shower cubicle using a sharp knife, then using a combination of power tools and blades we removed the grout in the affected areas and put in new white grout to match the exiting.

While the grout was drying, the shower tray was cleaned up and new silicone sealant has added around the base of the shower cubicle using a premium mould resistant silicone that should be more resistant to staining.

Ceramic Shower Tile and Grout After Revamp Sheffield

The combination of cleaning and grout replacement worked a treat and the shower looks like a brand-new installation. This doesn’t resolve the ventilation issue, so I left the customer with a bottle of Tile Doctor Aqua-Pro with instructions to spray the tiles down regularly in order to keep it looking fresh and clean.

Ceramic Shower Tile and Grout After Revamp Sheffield Ceramic Shower Tile and Grout After Revamp Sheffield

 

Source: Shower Tile Cleaning and Renovation Service in Hillsborough, South Yorkshire

Shower Cubicle Refresh to assist Property Sale in Derbyshire

This client lives in Chapel-en-le-Frith which is a small town dubbed the ‘Capital of the Peak’ with parts of the parish lying in the Peak District National Park. They were trying to sell the house, but the shower cubicle was looking very bad and all the potential purchasers were being put off. They wanted to restore a new and fresh look, without spending a fortune, so they could finally sell it and move to their new property. With this in mind they had given me a call to come and take a look and see what could be done.

As you can see from the photos the grout was very badly discoloured in places, so I agreed with the client that the best course of action would be to clean the grout as much as possible and then recolour it with a white Grout Colourant followed by stripping off the old silicone and replacing with new. We discussed the cost and a timescale and booked the job in.

Shower Cubicle Before Cleaning Chapel-en-le-Frith

Shower Cubicle Tile Cleaning

The Tile Doctor Grout Colourant Kit comes with everything you need to change the colour of your grout including a Pre-Treat cleaner which is a slightly acidic product that cleans and etches your grout at the same time. This means you can get a better bond with the colourant when it is applied afterwards and ensures the best finish.

I set about cleaning the grout with the pre-treat cleaner which is sprayed on to the tile and then scrubbed in with an abrasive pad. This was then rinsed off with water and re-applied where necessary, some areas were worse than others and needed more work, so I persevered until I was happy the grout was as clean as it could be.

Applying White Grout Colourant

The job could be completed in one day, so the next job was to remove the silicone sealant between the tiles and the shower tray, the sealant was black with mould and dirt and generally in very bad condition.

Once the grout had dried I was able to start the application of the grout colourant using a small brush, wiping any excess off the tiles as I went. A steady hand is required for this job along with a little patience! Two coats of colourant were required to achieve the right finish.

Finally, the last step to complete was to put back a new white silicone sealant using a high-quality mould resistant product. There are many on the market, but the cheaper brands are not usually mould resistant and tend to turn black very quickly. Applying the sealant ensures the shower is waterproof and no water can get behind the tiles.

Shower Cubicle After Cleaning Chapel-en-le-Frith

The shower cubicle had a new look and my client was really surprised about the end result. They now felt more confident that potential purchasers wouldn’t be put off by a grubby looking bathroom. Thankfully it had not cost them too much to make it look a whole lot more appealing.

Shower Cubicle After Cleaning Chapel-en-le-Frith

 

Source: Grout Cleaning and colouring Service in Derbyshire

Luxury Slate Shower Ruined by Limescale Restored in Surrey

In the south east of England, we suffer from hard water which as many of you have experienced can calcify on our showers leaving white limescale staining. Without fitting a water softener this limescale causes a problem around the home, particularly when the tiles are dark.

A good example of this problem was this large dark grey slate tiled shower at a house in Oxshott where the limescale had completely ruined the look of the black slate. The problem was most evident on the slate tiles on the floor but had also stained the slate split face slate tiles on the shower wall.

Slate Tiled Bathroom Before Renovation Oxshot

Oxshott is a village in Surrey between Leatherhead and Esher, a survey in 2010 by the Daily Telegraph asserted it was “the village with most footballers” in England and mentioned other celebrities who chose to live in the village probably because Chelsea Football Club have their main training ground in nearby Stoke D’Abernon; It is a beautiful area and is no surprise it is also known as ‘the most expensive village in England’.

The wet room was not that old, but due to the limescale staining was prematurely in need of attention. We often get calls from customers where they have use supermarket products to treat hard water stains, however these products are generally acidic, and this can make the problem worse. I would recommend you always read the back of the bottle before to check it is safe to use on natural stone before applying.

After inspecting the shower, I agreed with the client the best course of action, agreed a price and booked the job in for a later date.

Limescale Stained Slate Wet Room Cleaning

I returned on the agreed date and started work by first removing the existing sealer by applying Tile Doctor Remove and Go which is a multi-purpose stripper that’s formulated for use on natural stone. The product also draws out ingrained stains and removes heavy grease build-up. For best results spray the product onto the tile and then leave for it to soak in and get to work breaking down the coatings etc. After ten minutes the product is scrubbed into the stone which in this case meant by hand. The soiled solution can then be rinsed off the tiles with water. The grout was then cleaned by hand scrubbing in a strong dilution of Tile Doctor Pro-Clean followed by more rinsing.

The final part of preparation was to remove the limescale. This was done with a small handheld diamond block and a wire brush. The block is great for smoothing down all sorts of issues and being small it can get into tight areas. I then dried the whole room with an industrial blower. Slate cannot be sealed effectively when damp as it won’t cure properly. The blower is noisy but best in this situation and is very effective when a fast dry is needed.

Sealing a Slate Tiled Bathroom in Oxshott

After lunch I checked the area was nice and dry by testing the moisture content. I then sealed the whole area, wall and floor with Tile Doctor Colour Grow. Colour Grow, is a colour intensifying sealer that provides durable surface protection as well as allowing the surface to breath and enhance colour. For this project it darkened the tiles nicely and will provide protection from staining, making them much easier for the client to maintain moving forward.

The client was very happy with the lovely result. The bathroom looked clean and fresh again, now it is just a case of trying to keep on top of the limescale.

Slate Tiled Bathroom After Renovation Oxshot

 

Source: Slate Tile Cleaning and Renovation Service in West-Surrey

Renovating a Mouldy Marble Wet Room in Sheffield

The owner of this house in the village of Endcliffe Sheffield was unhappy about the state of their Marble wet room and called me in to do something about it. The main issue was that mould had built-up across the bathroom especially on the grout and silicone sealant, the Marble tiles were also looking dull and needed sprucing up.

Marble Bathroom Tiles Before Cleaning Endcliffe Sheffield

Dealing with Mould in a Wet Room

Mould thrives in moist warm conditions and without adequate ventilation it will start to take hold. Often in cases like this we advise clients to improve the power of their extractor fan or leave a window and a door open after a shower, in this case however the wet room had no windows. Another option you can try is to run the shower cold for a few minutes after you have used it, this decreases the temperature and removes moisture from the air. That tip is easily forgotten when your in a hurry so regular cleaning with Tile Doctor Duo-Clean which is a tile cleaner and mould remover should allow you to keep on top of the problem.

Marble Bathroom Tiles Before Cleaning Endcliffe Sheffield Marble Bathroom Tiles Before Cleaning Endcliffe Sheffield

In this case the Mould had really taken a hold and I knew form experience that scrubbing with a powerful cleaner like Duo Clean was unlikely to get the grout back to the pristine condition the customer wanted so I decided to strip out all the affected grout and silicone and replace with new. It took some time but I have a special electric grout removal tool that comes in handy for these situations and so it wasn’t long before I had removed the worse of it. This was followed by carefully removing the silicone sealant that ran between the shower tray and Marble wall tiles with a sharp knife.

Polishing Marble Wall and Floor Tiles

Next, I turned my attention to the Marble tiles which had lost their shine and become dull. Marble is hard stone and to get the best out of it we find its best to burnish them with a set of diamond encrusted burnishing pads that remove the dirt and slowly bring back the polished appearance. Normally when we talk about burnishing it’s in relation to stone floor tiles however these pads also come in small six-inch size as well which will fit a hand buffer or Angle Grinder.

Marble Bathroom Tiles During Cleaning Endcliffe Sheffield

Like floor burnishing the pads are applied in sequence starting with the coarse 400-grit pad and moving up through the 800, 1500 and finally the very fine 3,000-grit pad. The lower grit pads need to be lubricated with water and you rinse between each pad with water to remove the slurry that is generated.

Finishing the Marble Wet Room Renovation

With the Marble tiles now looking good it was time to protect them from future staining by sealing them with two coats of Tile Doctor Ultra-Seal which is a premium sealer that leaves a natural look that doesn’t darken the colour of the stone.

I left the re-grouting to last as its easier to remove grout from a sealed tile and then finished by putting back the silicone strip, both the grout and the silicone we chosen for their anti-mould formula and before leaving I gave some advice on how to keep on top of the mould problem going forward.

Marble Bathroom Tiles After Cleaning Endcliffe Sheffield

My client was delighted with the result and relieved that they would no longer feel embarrassed when visitors ask to use the bathroom.

Marble Bathroom Tiles After Cleaning Endcliffe Sheffield

 
 
Source: Marble Stone Cleaning and Polishing Service in Sheffield

Mould and Limescale stained Shower Cubicle renovated in Uxbridge

Ceramic and most Porcelain tiles are very easy to clean which makes them a good choice for shower cubicles, the one problem you will find though is that due to the cementitious nature of grout the top layer does attract dirt as can silicone. As a result, we recommend rinsing down showers with Tile Doctor Oxy-Pro on a regular basis or the problem will build. Mould can also be a problem especially if your bathroom is quite small or has inadequate ventilation to extract the hot steam in which mould thrives.

Ceramic Tiled Shower Cubicle Before Cleaning Uxbridge

This Ceramic tiled shower cubicle at a house in Uxbridge had all these problems and would need something much stronger to deal with the mould and remove the limescale which had also built up. Limescale from hard water is a problem that affects 60% of the UK with the South and East of England is particularly impacted due to the local chalk and limestone geology the water is filtered through. Buckinghamshire is known to have hard to very hard water and these tiny mineral deposits build up slowly on the surfaces of shower cubicles during use.

Deep Cleaning a Ceramic Tiled Shower Cubicle

To get the shower cubicle clean I began by spaying the tile and grout down with Tile Doctor Duo Clean which is a dual action product that is designed to clean grout and remove mould. You leave the product on the tiles for ten minutes and then scrub it in with a stiff brush, it’s hard work and you need to repeat in the stubborn areas, but it gets good results.

The tile and grout were then rinsed down with water and left to dry whilst I popped out for lunch. On my return I dried off any damp areas with a heat gun and took a step back to review the work I had done.

The results were good but unfortunately there were still a few dark stains in the grout which I was unlikely to be able to remove. When this happens, I find the best solution to achieve a consistent appearance is to apply a grout colourant to the grout. Tile Doctor grout colourants come in ten colours are relatively straight forward to apply, I always keep some of the popular colours in stock and on this occasion, I felt a White colourant would work best.

Normally the first stage would be to prepare the grout first with a pre-treater but given the grout had already been scrubbed hard I was able to move onto applying the colourant with a small brush. Grout Colourants not only recolour and rejuvenate the grout lines but also adds a barrier over the grout sealing it in and protecting it from further staining.

Whilst waiting for the colourant to dry I stripped out the mouldy sealant strip between the tile and shower tray and replaced with mould resistant silicone.

Ceramic Tiled Shower Cubicle Before Cleaning Uxbridge

The shower cubicle now looks much fresher and I’m sure will be a pleasure to take a shower in.
 
 
Source: Professional Renovation of a Ceramic Tiled Shower Cubicle in Buckinghamshire

Deep Cleaning Shower Tile Grout in Cumbria

We were asked to look at a renovating a bathroom shower at a house at the The Green, near Millom which was rather useful as it is a short distance from my own home. Millom is a small town in South West Cumbria that actually dates to 1251 when it was given a market charter by King Henry III.

Given the location it wasn’t long before I was able to pop round and review the shower installation. It was clear that the shower needed some Tile Doctor TLC, with mould being a major issue in the silicone seal and grout near the base of the shower.

Bathroom Shower Cubicle Before Renovation Millom

Mould thrives in warm damp environments such as shower cubicles and the problem can usually be traced to a lack of adequate ventilation. Improving the ventilation should resolve the problem permanently however if that’s not possible it can be controlled by regular use of products such as Tile Doctor Oxy-Pro shower cleaner or Tile Doctor Duo Clean which is a double action mould and grout cleaner. Other steps you can take include leaving the door open after a shower to improve cross ventilation and rinsing the shower down with cold water after a shower.

After reviewing the installation, we agreed on a price and I returned a few days later to carry out the work.

Cleaning Ceramic Bathroom Tile and Grout

On return the first thing we did was thoroughly clean the tile and grout using Tile Doctor Oxy-Gel, our high performance alkaline cleaner and de-greaser in gel form making light work of cleaning vertical tiled surfaces. The gel was scrubbed into all tile and grout surfaces and left to dwell for five minutes then thoroughly rinsed down with water. This process was repeated until we were happy with the result.

The next stage was to remove the mould riddled silicon and small areas of damaged grout at the base of the shower unit. This took some time to achieve as the silicon was in a very poor state. Once all traces of the silicone were removed we cleaned the area with more Oxy-Gel and carefully rinsed all the residues to stop us having any problems when re-applying new silicone.

Bathroom Shower Cubicle During Renovation Millom

The shower tray was cleaned of debris and a heat gun was used to completely dry all areas.

Replacing Shower Grout and Silicone Sealant

Finally, with the mould removed it was clear that a few areas of grout were crumbling and needed replacing. The old grout was raked out and a new batch of mould resistant grout was prepared and applied. Whilst that was drying I also replaced the silicone sealant between the shower tray and tile using a mould resistant silicone.

Bathroom Shower Cubicle After Renovation Millom

We asked the customer to not use the shower for at least 24 hours and as can be seen in the photographs the shower appearance was vastly improved. The customer is very pleased commenting that “it looks like new”.

Bathroom Shower Cubicle After Renovation Millom

 
 
Source: Tile and Grout Cleaning and Restoration Service in Cumbria

Renovating Three Shower Cubicles at Property in Sale, Cheshire

The photographs below are from one of three shower cubicles we were asked to clean and restore at a modernised Victorian property in SALE Cheshire. Ceramic tiles are glazed so very easy to keep clean, grout and silicone however are not and if you let mould build-up untreated it can very difficult to remove.

Mould likes a warm damp environment which can be reduced by improving the ventilation in the shower room, other steps you can take to reduce mould include always leaving the door open after a shower to improve cross ventilation and rinsing the shower down with cold water after a shower. Tile Doctor also have a product called Oxy-Pro that you can spray on your tiles after use.

Shower Cubicle Before Cleaning in Sale Shower Cubicle Before Cleaning in Sale

Sale is a town in Trafford, Greater Manchester but is historically part of Cheshire and dates to before the Middle Ages. A survey commissioned by the Royal Mail in 2017 highlighted Sale as the 4th most desirable town in England to live in and being so close to the city of Manchester makes it a popular choice for commuters.

Cleaning Ceramic Bathroom Tile and Grout

To get the grout clean Tile Doctor Pro-Clean was decanted into a spay bottle diluted with water and the solution was sprayed onto the grout lines. Pro-Clean in a strong and effective grout cleaner and after leaving it in place for about five minutes it was scrubbed in by hand using a stiff brush along the grout lines. I also gave the tile and cubicle glass a clean with Tile Doctor Oxy-Pro which comes in a ready to use spray bottle.

The next step was to carefully remove the old silicone sealant from around the edges of the shower cubicle using a sharp knife, so it could be replaced with new.

At this stage I took a step back to review the results of the cleaning, I wanted the best possible outcome for my customer and if more work was needed to get the shower looking it’s best now was the time. I concluded that the grout was much improved by unfortunately the mould staining was still visible in areas and that the best way to proceed would be to colour the grout.

Colouring Shower Tile Grout

Tile Doctor have a Grout Colourant product that’s available in ten different colours including White which I felt would be the best colour for the cubicle. Other colours include three shades of Grey, two shades of Brown and two shades of Beige as well as Black. The Grout Colourant is painted onto the grout lines using a small brush and I find a toothbrush works well for this purpose. Excess colourant needs to be removed from the tile before it sets, and I often find baby wipes work well for this purpose.

The grout colourant adds an epoxy barrier over the grout that is resistant to staining and much easier to clean than the grout itself. With this in place the grout will stay protected and the cubicle should keep its appearance for some time to come.

While the Grout Colourant was drying I replaced the silicone around the base of the shower cubicle using a premium mould resistant silicone that should be more resistant to staining.

Once the colourant and silicone had dried I gave the cubicle a final inspection and buffed up the ceramic tiles with a six-inch white pad fitted to a handheld buffer. As I mentioned before there were three shower cubicles to complete so as one was drying I was able to move onto another and as a result managed to complete all three in one day.

Shower Cubicle After Cleaning in Sale Shower Cubicle After Cleaning in Sale

 
 
Source: Shower Tile Cleaning and Renovation Service in Cheshire

Renovating Grubby Ceramic Tile and Grout in a Beckenham Bathroom

Recently I was asked to renovate the tile and grout of this windowless bathroom in a Beckenham flat which was not looking its best. The Ceramic tiles had become dull due to a build up of Limescale and the grout had become stained from shampoo dyes and mould.

Ceramic Bathroom Tiles Grout Before Cleaning Beckenham

Without strong ventilation and regular cleaning most bathrooms can end up with these problems however with the right products and techniques they can be renovated as you will see below.

Ceramic Bathroom Tiles Grout Before Cleaning Beckenham

Deep Cleaning Bathroom Tile and Grout

My first action was to apply a liberal amount of Tile Dr Oxy-Gel which is a strong alkaline tile and grout cleaning product that comes in a gel form. Being a gel it’s able to sticks to vertical surfaces for longer allowing it to break down the Limescale and soap residue that had taken up residence. Once it had been left to dwell for around thirty minutes, it was scrubbed off with water and a pan scrapper and then dried with a micro cloth. You can use this process with glazed ceramic tiles like these but for natural stone I would have used a different approach.

I then sprayed Tile Doctor Duo Clean, which is a grout cleaner and mould remover, onto the grout lines. I left the grout with the Duo Clean on it for about ten minutes before scrubbing and rinsing off with water.

The process was repeated where needed until I was happy that the tile and grout were as clean as possible however to really give the bathroom a fresh look I decided to completely renovate the grout with the application of a Grout Colourant.

Grout Colouring Bathroom Wall Tiles

There are ten colours to choose from in the Tile Doctor range of Grout Colourant’s and in this case I felt the best outcome would be to use a White colourant to match the tiles and restore the original look of the bathroom; the customer however wanted a grout colour that would provide a contrast against the white tiles, so in the end we opted for a light grey colour.

The colourant is easily applied directly to the grout and in this case I waited for the tiles to dry before applying two coats with the aid of a small brush making sure to remove any excess that comes into contact with the tile.

I finished the renovation by cutting out the original mastic sealant from around the bath and replacing with a new mould resistant silicone in white to match the bathtub.

Ceramic Bathroom Tiles Grout After Cleaning Beckenham

The bathroom now looks transformed and the epoxy grout colourant adds a layer of protection to the grout that will keep it looking good for some time to come.
 
 
Source: Bathroom Tile Cleaning and Restoration Service in Kent

Restoring Water Stained Porcelain Shower Tiles

Photographs below of a Porcelain tiled shower that had been installed at a house in Cheshunt the year before. The tiles were actually dark grey textured porcelain tile but hard water in the area had left very noticeable water stains and limescale deposits that were proving hard to remove with general cleaning.

Stained Black Porcelain Shower Tile Cheshunt Before Cleaning

Hardwater is basically water with a high mineral content which are historically recognised as being good for you, however it’s not so good for the bathroom where the minerals are left behind when the water evaporates.

On the initial visit to survey the tiles we ran a test clean on a small area to ensure we could return the tile back to its as new condition. All went well, and the customer booked us in to return later to complete the work.

Removing Limescale from Porcelain Shower Tiles

Work began by giving the shower tiles an initial clean with Tile Doctor Aqua-Pro which was worked into grout lines with detail brushes and a burnishing pad for the tile surface. This process removed all the Limescale and water marks.

A second clean was then carried out with Tile Doctor Duo-Clean which is a fast-effective double action cleaning solution that can remove mould and blackspots from grout and silicone. The solution was sprayed on the shower room floor and walls and left to soak in before being worked in with a stiff brush.

Stained Black Porcelain Shower Tile Cheshunt During Cleaning

The shower tiles were then rinsed with a steam cleaner to remove any trace of product and then buff the tiles with a hand-held white buffing pad to bring up their appearance.

To give it a neat waterproof finish we stripped out the old silicone sealant from around the base of the shower and replaced with new mould resistant silicone.

The shower took a whole day to complete but I think you will agree has been transformed by the process.

Stained Black Porcelain Shower Tile Cheshunt After Cleaning

Reducing the Impact of Hard Water

To minimise the impact of hard water some shower units will keep the shower running at a gradually decreasing temperature immediately after use. This has the effect of rinsing off the deposits before evaporation has chance to occur. Personally, we recommended you spray the shower tiles with Tile Doctor Aqua-Pro after use, this product is a bathroom tile cleaner that is ideal for the regular cleaning of all types of internal porcelain/ceramic bathroom/wet room tiles. Apply by lightly spraying a dilution of the cleaner and wipe over then water rinse and dry buff to finish.
 
 
Source: Porcelain Tile Cleaning and Renovation Service in Hertfordshire

Stained Shower Cubicle Renovation in Hove, East Sussex

Hove is a town in East Sussex which is confused with – and somewhat overshadowed by – its larger, more well-known neighbour, Brighton. In fact, the tendency for people to confuse Hove and Brighton is such that a running joke in the area amongst residents of Hove is to reply “Hove, actually” when they are asked if they live in Brighton.

But Hove is no small town – in fact, its home to more than 90,000 people. As the East Sussex Tile Doctor I am a frequent visitor to the Brighton and Hove area. Most recently, I was called to a property to address a Porcelain tiled shower cubicle which was really starting to annoy the owner.

She felt like she could never seem to keep it clean of grime and the dyes in soaps that invariably stain the grouting. As a result, the whole cubicle looked worse for wear – you can see this in the photo below.

Shower Room Tiles Before Grout Colouring in Hove Shower Room Tiles Before Grout Colouring in Hove

Not only did the customer want the tiles and grout cleaned up, but she had been impressed by some subway tiles she had seen where a darker grout had been used, she liked the effect it gave and wanted to see if it could be replicated. I suggested that we could clean up the tiles and recolour the grout using a Black Tile Doctor Grout Colourant. She accepted the quote for the work and I was able to get started soon after.

Cleaning Porcelain Shower Tiles and Grout

To begin the restoration, I gave the tile and grout a deep clean using Tile Doctor Pro-Clean, which is a highly effective alkaline-based cleaner for Tile, Stone and Grout.

This left the tiles looking fresher, but the grout lines – which were very badly stained – would as need to be recoloured for the best result. Before applying the Grout Colourant, the grout needed to be prepped in order to achieve a strong bond with the colourant. To do this I applied Tile Doctor Grout Clean-Up which is an acidic product normally used for removing grout smears but in this case, I used it to etch the surface of the grout. Once done I gave the grout a rinse with water to remove any trace of cleaning product.

Recolouring Shower Tile Grout

The final step in the restoration was to recolour the grout in black to achieve that subway effect the customer desired. There are actually ten different colours in the Tile Doctor Grout Colourant range, including Charcoal Grey, White, and Chocolate, as well as Black.
The colourant in basically painted onto the grout using an applicator brush, you then let it dry for a while and then wipe off any excess from the tile surface. It looks a little horrendous in the photographs above but wait until you see the final result.

Shower Room Tiles During Grout Colouring in Hove Shower Room Tiles During Grout Colouring in Hove

Once the grout colourant sets you find that not only does it effectively recolour and rejuvenate the grout, but it also makes a barrier over the grout effectively sealing it in and making it easier to clean in future.

The last step was to strip out the mould stained silicone sealant from around the base of the shower cubicle and replace with a quality mould resistant sealant. This final step really finished off the renovation and the photographs below show the outcome, which I think you will agree was quite a transformation. Thankfully, it was exactly what the customer was looking for!

Shower Room Tiles During Grout Colouring in Hove Shower Room Tiles After Grout Colouring in Hove

 
 
Source: Shower Tile and Grout Cleaning and Renovation Service in East Sussex